background image

 7 

HAMPTONBAY.COM 

 

 

Please contact 1-855-HD-HAMPTON for further assistance. 

Installation (continued)  

 

 

5

 

Mounting the  Transformer 

6

Mounting the Photocell 

To mount directly to a wall surface use the included screws (AA) as 
shown, suitable for mounting within 12 in. to 48 in. (0.3 m  to 1.2 m) 
of the ground. When installing the screws, the spacing between the 
screw centers is 3.35 in. (85 mm). See the template (D) for correct 
spacing. Hang the transformer (A) onto the screws (AA). 

 
 
 
 
 
 
 
 
 
 
 
 

Mount the photocell (B) bracket on a wall or other solid surface with 
the screws (BB)

 

provided. Snap the sensor into the bracket. Route or 

coil the excess wire to protect it from lawn mowers, trimmers, etc. 
Avoid pointing the sensor at nighttime light sources such as 
windows, porch lights, and street lights.  

 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 

Placing the sensor in  areas receiving less sunlight at dusk (east side 
of house, behind trees and bushes, under a deck) will have the 
transformer come on earlier in the evening. Mounting the photocell in 
brighter locations will have the transformer come on when it has 
become darker out. The location, position and orientation of the 
photocell  can be adjusted until the transformer turns on at the 
desired light level. 
If the wires to the photocell are cut or broken, the photocell can 
be replaced. Unscrew the photocell connector cover from the 
transformer and pull the bi-pin connector out of the mating socket. 
The replacement part is inserted into the socket and the cap is 
screwed back onto the socket to provide a water tight connection. 
Note that the bi-pin connector is polarized and can be inserted into 
the socket only one way. The photo eye operation can be tested by 
turning the transformer mode to TEST. 
Replacement photocell is available in the store. 
Cover the connection hole with the dust cap when no photocell 
control wire is connected. 

 

 
 
 
 
 
 
 

 

Once all fixtures are in place and you are satisfied with their  
locations, the cable may be covered with mulch or buried up to  
6 in. (15 cm) deep. Leave about 12 in. (30 cm) of cable after the  
last fixture. 

 

 
 
 
 

7

 

Protecting or Hiding the Cable 

 

WARNING: Risk of Fire 

DO not coil cable  around  transformer. Total bulb 
wattages must not exceed a maximum of 200 watts.

 

Summary of Contents for SL-200-12A












Reviews: