HAMPTON BAY GCI60 Technical Manual Download Page 31

Please Note

 - Burning Corn or Grains - Burning corn or other grains creates a harsher environment than burning wood pellets. The sugar in corn 

turns to acid during the combustion process and erodes certain components at a faster rate. The burn pot liner and the agitator in your Multi - Fuel 
stove is a consumable item when burning corn or other grains, and not covered under warranty. We expect that these components will last a couple 
of burn seasons but due to the wide variety and quality of grains we are not able to accurately predict how long they will last.

Hampton GCI60 Cast Pellet Insert Technical Manual

31

FPI is the manufacturer of the Hampton line of heating products. At FPI, our commitment to the highest level of quality and customer 
service is the most important thing we do. Each Hampton stove is built on a tradition of using only the 

fi

 nest materials and is backed 

by our Exclusive Lifetime Limited Warranty to the original purchaser. With Hampton, you’re not just buying a stove, you’re buying a 
company with years of unequalled performance and quality.

Limited Lifetime Warranty:

Under this warranty, FPI covers the 

fi

 replace or stove body and accessories against defects in materials and workmanship, for part 

repair or replacement for the 

fi

 rst seven (7) years and limited labour for the 

fi

 rst two (2) years to the original purchaser. This Warranty 

covers: Firebox, Heat Exchanger, Burn Pot, Firebox Panels, Ceramic Glass, Pedestals, Panels, Legs, Log Sets and Door Assembly. 
Please see the exclusions and limitation section below as certain restrictions and exclusions apply to this warranty.

Limited Three (3) Year Warranty:

Under this warranty, FPI covers the Burn Pot Liner against defects in materials and workmanship, for part repair or replacement for 
the 

fi

 rst three (3) years and limited labour for the 

fi

 rst two (2) years to the original purchaser. Please see the exclusions and limitation 

section below as certain restrictions and exclusions apply to this warranty.

Limited Two (2) Year Warranty:

Under this warranty, FPI covers: Auger Motor, Circuit Board, Timers, Temp Sensors, Blowers, Vacuum Switch and Wire Harness, 
against defects in materials and workmanship, for part repair or replacement for the 

fi

 rst two (2) years and limited labour for the 

fi

 rst 

two (2) years to the original purchaser. Please see the exclusions and limitation section below as certain restrictions and exclusions 
apply to this warranty.

Limited One (1) Year Warranty:

Under this warranty, FPI covers the Ignitor and all exterior surface 

fi

 nishes against defects in materials and workmanship, for part 

repair or replacement and limited labour for the 

fi

 rst (1) year to the original purchaser. Please see the exclusions and limitation section 

below as certain restrictions and exclusions apply to this warranty.

Here is how our Warranty works:

If you have any concerns with your Hampton product please contact the dealer where you purchased the 

fi

 replace or stove. Your 

dealer shall make all claims under this warranty in writing.

To the Dealer:

When 

fi

 lling out a warranty claim please complete the following information on an of

fi

 cial warranty claim form: 

Customer information: Name, address and telephone number of purchaser and date of purchase.
Dealer information: Date of installation, name of installer and dealer, serial number of the appliance, nature of complaint, defects or 
malfunction, description and part numbers of any parts replaced.

To the Distributor:

Sign and verify that work and information are correct.

WARRANTY

Summary of Contents for GCI60




































Reviews: