HAMOKI TP-22L Instruction Manual Download Page 7

have a high temperature, and the operator should also be especially careful when 
handling as to avoid burns. 

3. 

Once frying is finished, operators should utilise the handle at the top of the basket to 
help prevent the basket from getting too hot. A hook is placed outside the pot to 
allow you to hang the basket above to filter out the remaining oil. The basket can be 
fried directly in the pot, but it is necessary to prevent the suspended matter from 
clogging the exhaust device. 

4. 

The maximum working temperature of the pressure fryer is 200°C. When the 
temperature control fails, or the oil temperature exceeds 230°C, the over-
temperature protector (temperature limiter/high-limit thermostat) will kick in, and the 
heating power will automatically be cut off. This protector will need to be reset 
manually, and is located at the bottom front of the pot. Only when the oil temperature 
is cooled to below 80-100°C, can the reset button be pressed to restart the electric 
heating. 

5. 

It is recommended to wear insulated gloves when operating the machine to avoid 
burns and other serious injuries. 

 

CLEANING PRECAUTIONS

 

The pot body of the pressure fryer is moulded by aluminium and requires cleaning every 
day after use. If not cleaned, the oil stains and sediments left are prone to coking, and 
this is very difficult to clean and remove later.   

 
The inside of the fryer should be cleaned daily. If left, oil and breading deposits can 
become burnt on and be very difficult to clean. 

 

1. 

When cleaning the pressure fryer, fill 3/4 way with water and add dishwashing 
detergent. Whilst it is still warm, use a hard bristle brush or a cleaning ball to clean 
the inside, but do not use hard cleaning tool (metal cleaning ball) to avoid damage to 
the inner pot. 

2. 

When cleaning, be sure the unit is switched off and there is no power on, otherwise 
the material inside will heat up or cause the pan to overheat and get burnt. 

3. 

Beware of using chemical cleaners that are suitable for use with aluminium. 
Corrosion can occur with many products. Particularly those containing caustic soda. 

Hamoki cannot accept responsibility for damage caused using corrosive 
cleaning products.

 

4. 

Be careful when cleaning the drainpipe and drain valve. There will be debris in the 
drainpipe. Before cleaning the drainpipe, the drain valve should be fully open, taking 
care not to damage the ball valve or its seal. 

5. 

Be careful to remove all the water and any remains of cleaning materials before use. 

Summary of Contents for TP-22L














Reviews: