Page 33
Result: Notice absence of vibrato effect
c. Mode Switch Operation (Vibrato Functions)—VIBRATO
1. Control Panel Tabs:
OFF
Selector switch:
GUITAR
Mode switch:
VIBRATO
Action:
Play chord on upper manual
Result: Notice vibrato effect
d. Mode Switch Operation (Vibrato Functions)—DELAYED
VIBRATO
1. Control Panel Tabs:
OFF
Selector switch:
GUITAR
Mode switch:
DELAYED VIBRATO
Action:
Play chord on upper manual
Result: Notice that vibrato effect begins approximately .6
seconds after chord is pressed.
e. Mode Switch Operation (Reiteration Functions)—NORMAL
1. Control Panel Tabs:
OFF
Selector switch:
GUITAR or CHIME
Mode switch:
NORMAL
Action:
Play chord on upper manual
Result: Percussion repeats at the following rates:
FAST:
11.2 Hz
MEDIUM:
7.7 Hz
SLOW:
5.4 Hz
f. Mode Switch Operation (Reiteration Functions)—MARIMBA
or XYLOPHONE
1. Control Panel Tabs:
OFF
Selector switch:
MARIMBA or XYLOPHONE
Mode switch:
NORMAL
Action:
Play chord on upper manual
Result: A reiterative sound of different quality than in
step
e
is heard. The two harmonics used in these voices
are turned on and off at opposite times. This is known as
“alternate reiteration”.
g. Cymbal-Brush Switch Operation—OFF
1. Lower Manual:
DRAWBARS depressed
Cymbal-Brush switch: OFF
Action:
Play lower manual
Result: Lower manual function should be normal.
Drawbar functions should be normal.
h. Cymbal-Brush Switch Operation—ON (Low, Med, High)—
Lower Manual
1. Lower Manual:
DRAWBARS depressed
Cymbal-Brush switch: Any position
Action:
Play lower manual
Result: Drawbar #7 should be inoperative.
2. Lower Manual:
DRAWBARS up (off)
Cymbal-Brush switch: LOUD
Control Panel Tabs:
BRILLIANCE on
Action:
Play any lower manual key
repeatedly (other than highest 6 keys on right-side of
manuals).
Result: The result should be a percussive hiss sound of
1.0 V ± 3 db rms measured across 12” speaker leads.
R602 may be adjusted to obtain the proper levels. R602
is located on terminal strip assembly, AO–31213–1.
i. Cymbal-Brush Switch Operation—ON (Low, Med,
High)—Pedals
1. Cymbal-Brush switch: LOUD
Control Panel Tabs:
BRILLIANCE on
Action:
Play any pedal repeatedly
Result: The result should be a percussive hiss sound of
1.25 V ± 3db rms.
NOTE 4–6–A
When the BRILLIANCE tab is turned off, volume of Brush and Cymbal
is decreased.
Summary of Contents for L-100 Series
