background image

 

21 

Hammer Engines GmbH / IQ-Serie / Instruction Manual 

 
 

Activates the Telemetry transmitter (TRX-2400). 
Amount of Data packets per time unit (OFF/1x/2x/3x), 
channel transmitted on (COM-CHANNEL 0-10) and the 
address of the Graphic-Telemetry (0-10000).  Please 
refer to the corresponding manuals for further 
information. 

 

 

 

 

IMPORTANT ! 

This will reset the ECU to factory settings. 

 
 
 
___________________________________________________________________________ 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

 
Menu point 4 will display stored as well as current GPS and Airspeed-date generated by 
the GAS-Module.
  
 

Latitude and Longitude:

 

Displays current Geo-Information in Latitude  and Longitude. 
 

UTC-TIME – valid positioning – Heading – Satellites:

 

UTC (U): The second screen displays the UTC-Time in H-M-S format. Depending on the 
time zone you will need to add or subtract accordingly. 
Valid positioning (NOK-OK-3D): The top right corner shows whether your current 
positioning is valid. As follows: NOK = not OKay, OK. = OKay, but only in 2D and 3D. = 
OKay in 3D . 
Heading (C): Heading in degrees. 
Satellites (SAT): Amount of satellites connected at the moment. The higher the amount the 
more precise will the read out GPS positioning will be. As a rule you should be connected to a 
minimum of 7 satellites. 
 

 
 

 
 

Summary of Contents for IQ-H 130+




































Reviews: