background image

3

1.

Read the Operation Manual before using blender.
Keep Operation Manual handy.

2.

Plug into a grounded 3-prong outlet.

3.

Do not remove ground prong.

4.

Do not use an adapter.

5.

Do not use an extension cord.

6.

Disconnect power before cleaning or servicing.

7.

To reduce risk of personal injury, unplug cord from 
outlet when not in use, and before putting on or 
taking off parts.

8.

To protect against electrical shock, do not immerse
cord, plug, or blender base in water or any other
liquid.

9.

Do not spray the base with a high-pressure spray gun.

10.

Extreme caution must be used when moving an 
appliance containing hot oil or other hot liquids.

11.

Do not use appliance for other than intended use.

12.

Not intended for use by or near children.

13.

The use of accessory attachments not recommended
by the appliance manufacturer may cause injuries.

14.

To reduce risk of personal injury and to prevent 
damage to blender or container and cutter assembly,
DO NOT insert utensils into blender container while
operating blender.

15.

Do not store any kitchen utensils in the container
because the blender would be damaged if 
inadvertently turned on.

16.

To prevent possibility of serious personal injury, keep
hands out of blender jar while operating blender.
Always operate blender with jar cover in place.

17.

Avoid contacting moving parts.

18.

Blades are sharp. Handle carefully.

19.

If cutter assembly blades are loose, discontinue use
immediately and replace cutter assembly. Do not
attempt to repair or tighten cutter assembly.

– 

SAVE THESE IN STRUC TIONS

20.

Inspect container and cutter assembly daily. Do not
use broken, chipped, or cracked container. Check
cutter for wear, nicks, or broken blades. Do not use
broken or cracked cutting blades. Replace cutter
assembly at least every 90 days.

21.

Do not use outdoors.

22.

This appliance is intended for short periods of 
operation, with a rated operating time of 3 minutes.

23.

Do not leave blender unattended while it is operating.

24.

To prevent damage to blender, container, or cutter
assembly, DO NOT move or shake blender while in
operation. If blending action stops during operation, 
turn blender OFF, remove container from base, remove
container cover, and use a thin rubber spatula to push
mixture towards cutters.

25.

To prevent burns from hot liquids splashing out of the
container, always remove the filler cap of the container
cover before blending hot liquids. Keep hands and
other exposed skin away from the cover opening to
reduce risk of possible injury.

26.

Always operate blender with container cover in place.

27.

Do not operate any appliance with a damaged cord or
plug or after the appliance malfunctions, or is dropped
or damaged in any manner. Call the Technical Service
number, 

866-285-1087 

or 

910-693-4277

, for instructions

on examination, repair, or electrical or mechanical
adjustment.

28.

This appliance is not intended for use by persons 
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision 
or instruction concerning use of the appliance by a
person responsible for their safety.

29.

Children should be supervised to ensure that they 
do not play with the appliance.

IMPORTANT SAFETY INSTRUCTIONS

WARNING – 

When using electrical appliances, basic safety precautions should be followed, including

the following:

Blender Safety

WARNING!

Shock Hazard: This product is provided with 

a grounded (3-prong) plug to reduce the risk of electric
shock. The plug fits only one way into a grounded outlet.
Do not defeat the safety purpose of the plug by modifying
the plug in any way or by using an adapter. If the plug does
not fit into the outlet, have an electrician replace the outlet.

The length of the cord used on this appliance was selected
to reduce the hazards of becoming tangled in or tripping
over a longer cord. If a longer cord is necessary, an
approved extension cord may be used. The electrical rating
of the extension cord must be equal to or greater than the
rating of the appliance. The extension cord must be a
grounding-type, 3-wire cord. Care must be taken to arrange
the extension cord so that it will not drape over the
countertop or tabletop where it can be pulled on or
accidentally tripped over.

OTHER CONSUMER SAFETY INFORMATION

Summary of Contents for HBB908 - Bar Blender, 44 oz. Poly Top





























Reviews: