27
Subject to change without notice
Menu
The instrument software contains several menus. The
controls regarding the menus are described under item
(40)
PRINT / MENU
in section ”Controls and Readout”.
The following menus, submenus and items within the
submenus are available:
1.
MAIN MENU
contains:
1.1
CALIBRATE
Information regarding this can be found in the
section ”Service Instructions” item ”Adjustments”.
1.2
SETUP
This menu allows changes to the default settings
regarding the instrument behavior during operation.
The
SETUP
menu contains the submenus
”MISCELLANEOUS”
and
”FACTORY”
.
1.2.1
MISCELLANEOUS
contains:
1.2.1.1
CONTROL BEEP ON/OFF
.
In OFF condition the acoustic signals actuated by
the control limits are switched off.
Note:
The default setting is ON. If different conditions
are required the setting must be performed
each time after switching the oscilloscope on.
1.2.1.2
ERROR BEEP ON/OFF
.
Acoustic signals indicating faulty control operation
are suppressed in
OFF
condition.
Note:
The default is ON. If different conditions are
required the setting must be performed each
time after switching the oscilloscope on.
1.2.1.3
QUICK START ON/OFF
.
In condition
ON
the
HAMEG
logo and the menus
will not be displayed after switching the instrument
on. Then the instrument is quickly ready for
operation. To change from
QUICK START OFF
to
ON
, press and hold the
AUTOSET
pushbutton when
switching the instrument on until the menus become
visible and change the setting from
ON
to
OFF
.
1.2.1.4
TRIG.-SYMBOL ON/OFF
.
In most of the
Yt
(time base) modes the readout
displays a trigger point symbol which will not be
displayed in condition
OFF
.
1.2.1.5
DC REFERENCE ON/OFF
.
If
ON
is selected and
Yt
(time base) mode is present,
the readout displays a ground symbol (
⊥
⊥⊥
⊥⊥
). This symbol
eases the evaluation and determination of DC
contents by indicating the 0 Volt reference position.
1.2.1.6
EXTENDED CURSOR ON/OFF
.
If
ON
is selected and
Yt
(time base) storage mode
is present, additional cursor measurement functions
are available. For further information please note item
ON/OFF – CHI/II – 1/
∆∆∆∆∆
t
(41)
in section “Controls
and Readout”.
1.2.1.7
INPUT Z ON/OFF
In condition
ON
the
TRIG. EXT. / INP. (Z)
BNC socket
can be used for trace intensity modulation if analog
mode is active. For further information please note
“Readout and Controls”.
1.2.2
FACTORY
Attention!
The submenues are available only for HAMEG
authorized workshops, due to very expensive
required in connection with oscilloscope adjustment.
1.3
HO79
This information will only be displayed if the interface
HO79-
6
is connected to the oscilloscope.
For further information please note the HO79-6 manual
which is supplied with the interface.
First Time Operation
The following text assumes that the
“SAFETY”
section of
this manual has been read carefully and understood.
Each time before the instrument is put into operation check
that the oscilloscope is connected to protective earth. For
that reason the power cable must be connected to the
oscilloscope and the power outlet. Then the test lead(s) must
be connected to the oscilloscope input(s). Check that the
device under test is switched off and connect the test lead(s)
to the test point(s). Then switch on the instrument and after-
wards the device under test.
The oscilloscope is switched on by depressing the red
POWER
pushbutton. After a few seconds the HAMEG logo
and the instrument software release is displayed on the
screen. As long as the
HAMEG
logo is visible different internal
checks are made. Thereafter the instrument will revert to its
last used operating mode.
If after approx. 20 seconds no trace is visible, the
AUTO SET
pushbutton should be pressed briefly. This selects the Yt mode
and medium trace and readout intensity (
please note “AUTO
SET”
). Adjust
Y-POS.I
and
X-POS.
controls to center the
baseline. Adjust
INTENS.
(intensity) and
FOCUS
controls for
medium brightness and optimum sharpness (input(s) groun-
ded) of the trace. The oscilloscope is now ready for use.
If the
AUTO SET
function was not used and only a spot
appears (
CAUTION! CRT phosphor can be damaged
), redu-
ce the intensity immediately and check that the
XY
mode is
not selected (
XY
not displayed in the readout).
To obtain the maximum life from the cathode-ray tube, the
minimum intensity setting necessary for the measurement
in hand and the ambient light conditions should be used.
Particular care is required when a single spot is displayed, as
a very high intensity setting may cause damage to the
fluorescent screen of the CRT. Switching the oscilloscope
off and on at short intervals stresses the cathode of the CRT
and should therefore be avoided.
The instrument is so designed that even incorrect operation
will not cause serious damage.
Trace Rotation TR
In spite of Mumetal-shielding of the CRT, effects of the earth‘s
magnetic field on the horizontal trace position cannot be
completely avoided. This is dependent upon the orientation
of the oscilloscope on the place of work. A centered trace
may not align exactly with the horizontal center line of the
graticule. A few degrees of misalignment can be corrected
by a potentiometer accessible through an opening on the
front panel marked
TR
.
Menu
First Time Operation
