background image

 

Chapter 1. Introduction

 

 

 

EQ-77X LDLS® Operation Manual

5

 of 

31

 

 

Chapter 1. Introduction

The EQ-77X

 Laser-Driven Light Source (LDLS®) is a broadband lamp system for use in a wide variety of applications. 

The lamp produces high brightness, broadband light from DUV wavelengths through visible and beyond. The output is 
very stable, and has a long lifetime before any service is required. A simple control interface ensures ease of use.

 

Some of the advantages of the EQ-77X

 system include:

 

The EQ-77X

 system consists of a power supply controller unit, lamp head unit, and interconnecting cable. Connection 

to AC power is required for operation. Connection to cooling fluid is required. Connection to nitrogen purge gas is 
strongly recommended for best performance.

 

For additional information, contact Energetiq

 Technology Technical Support Services at +1-781-939-0763 x111 or 

email: 

[email protected]

.

 

Very high brightness across complete spectrum

190nm through visible and beyond

Eliminates need for multiple lamps (replaces D2/Tungsten/Xenon Arc) 

Simplified optical system

Excellent spatial stability

Repeatable measurements

Superior short and long term power stability

Repeatable measurements


Electrodeless operation for long life

Reduced consumable costs 

Minimal recalibration of instrument

Summary of Contents for ENERGETIQ LDLS EQ-77X
































Reviews: