SPECIFICATIONS
●
CCD CAMERA
●
OVER-LIGHT PROTECTION (OLP), AUTO GAIN CONTROL (AGC)
●
CONTROL METHOD
●
POWER SUPPLY AND ENVIRONMENTAL SPECIFICATIONS
3
Parameter
Effective Number of Cells (H
×
V)
CCD Gain
Total
γ
Characteristics
Scanning Frequency/Horizontal
Scanning Frequency/Vertical
Scanning
Video Out
Synchronization Method
External Synchronization Input
Allowable External Synchronized Frequency Deviation
(Adjust Horizontal Synchronized Frequency)
Jitter (Adjust Horizontal Synchronized Frequency)
EIA
Signal System
768
×
494
15.734 ± 0.157 34
59.94 ± 0.5994
525 lines, 2: 1 interlace
Imaging System
Adjust by the knob at the rear panel
1.0 (Switchable to 0.45)
1.0 V p-p, 75
Ω
unbalanced
Internal/External (Auto Selection by the Input Signal)
S, VS (SYNC Level: 0.3 V p-p), HV/VD (HD/VD level: 2 V to 5 V p-p) (Auto Selection by the Input Signal)
±1
±50
CCIR
Unit
—
—
—
kHz
Hz
—
—
—
—
%
ns Max.
752
×
582
15.625 ± 0.156 25
50 ± 0.5
625 lines, 2: 1 interlace
Parameter
Detection Method
Control Method
AGC Operation
OLP Operation
Delay Time for protection circuit to
function after the event of over-light
AGC (Auto Gain Control) Monitor
Over-light Protection Reset Input
Operation
Indication
Operation
Indication
Detect the average value of video signals
Control the image intensifier gain
Change the image intensifier gain to maintain the output image of image intensifier brightness at a constant level
PROTECTION LED (red) flashes
Turn off the image intensifier
PROTECTION LED (red) light up continuously
500 ms Max.
TTL negative logic, AUX connector pin No. 4 (During AGC)
Input impedance: 1 k
Ω
, TTL positive Logic
Description/Value
Parameter
Gain Control
(Image Intensifier)
Shutter
Operation
External Synchronization
by HD, VD
Internal Synchronization Mode (INT Mode)
External Pulse Control Mode (PULSE Mode)
Normal Mode
Camera Head Rear Panel
5-pin AUX Connector
HD
VD
Manual (10-rotation vernier knob)
(Not adjustable when the protection circuit is in operation)
+5 V dc to +9 V dc
Internal frame signal (VD signal) synchronization
Shutter timing is controlled by the width of external pulses
Continuous operation (shutter open)
Pulse height: 2 to 4 V p-p
Input Impedance: 75
Ω
TTL: synchronization negative
Pulse width: 10 µs or over
Frequency: 15.73 kHz ±0.3 kHz (15.625 kHz ±0.3 kHz)
A
Pulse height: 2 V to 4 V p-p
Input Impedance: 75
Ω
TTL: synchronization negative
Pulse width: 200 µs or over
Frequency: 59.94 Hz ±1.2 Hz (50 Hz ±1 Hz)
A
Description/Value
Parameter
Power Supply
Power Consumption
Operating Ambient
Condition
Storage Temperature
Weight
Dimensional
Outline
Accessory
A
( ): CCIR signal system
Video monitors for use in Japan conform to EIA signal system.
Temperature
Humidity
C5909, -01, -02, -03, -10, -11, -12, -13
C5909-06, -07, -08, -09
C5909, -01, -02, -03, -10, -11, -12, -13
C5909-06, -07, -08, -09
+12 (+10.5 to +15)
4.4
0 to +40
RH 70 or below (without moisture condensation)
-20 to +50
1040
1070
66(W)
×
71(H)
×
216.8(D) (Excluding projection part)
66(W)
×
68(H)
×
216.8(D) (Excluding projection part)
Lens Mount Cap, Instruction Manual, Test and Inspection data
V dc
W Max.
°
C
% RH
°
C
g
g
mm
mm
—
Description/Value
Unit
