Charging Hole
Pothook in right ear
Pothook in left ear
Pothook pole
Terminate a call
When finishing your call, press the TALK button on your headset.
The call will be disconnected.
Voice dialling (dialling using a name)
1.
Turn your headphone on and pair it with your mobile phone (if you have not done so already)
2.
Press the Multifunction key for about 1 second until your hear a "DU" tone.
3.
You can hear a short signal. Speak the name of the person you want to call.
4.
Your phone now dials the corresponding phone number. .
For you to use voice dialling through the headphone, your mobile phone must support this feature and
appropriate voice samples must have been stored.
Redial
Press on the key for about 2 seconds while your headphone is on standby (no conversation run-
ning) until you hear a Du-Du-Du-Du- tone. Your mobile phone will dial the last called number again.
Adjust the Volume
Press the and - buttom to adjust volume.
Visual indicators
Blue LED and red LED indicate the Status of the headset:
Visual LED-Table:
Status
Indication
Turning on
Blue LED flashes 5 times
Turning off
Red LED flashes 5 times
Pairing-Mode
Blue and red LEDs flashes alternately
Standby-Mode
Blue LED flashes 2 x per second
Battery 60% full
Red LED is off
Battery is low
Red LED goes on
Safety references:
Please read the operating instructions carefully, before using your Headset.
-
Do not dismantle your headphone.
-
Protect your headphone from dirt and dust.
-
Avoid exposing your headphone to high temperatures.
-
Switch your headphone off in aeroplanes and petrol stations.
-
Keep your headphone out of reach of children. Small pieces of the headphone could work loose and be
swallowed.
Please note
:
-
The warranty is limited to the original purchaser.
-
A copy of your receipt or other proof of purchase is required. Without proof of purchase, your warranty
is defined as beginning on the date of manufacture as labeled on the products.
-
The warranty is void if the serial number, date code label or product label is removed, or if the product
has been subject to physical abuse, improper installation, modification, or repair by unauthorized third
parties.
-
The responsibility for our products is limited to the repair or replacement of the product at our discretion.
-
All warranty on our products is limited to two years from the date of purchase.
-
Specifically exempt from any warranty are limited-life consumable components subject to normal wear
and tear, such as microphone, decorative finishes, batteries, and other accessories.
-
We are not liable for any incidental or consequential damages arising from the use or misuse of any our
products.
-
This warranty gives you specific rights but you may have other rights depending on your location.
-
Unless otherwise instructed in the user guide, the user may not, under any circumstances, attempt to
perform service, adjustments or repairs on this unit, whether in or out of warranty. It must be returned
to the sales outlet, factory or authorized service agency for all such work.
-
We do not assume any responsibility for any loss or damage incurred during shipping. Any repair work
on our products by unauthorized third parties nullifies any warranty.
User Manual
Thank you for purchasing BH-2. BH-2 is a earclip cordless headset that enables comfortable handsfree
communication with your Bluetooth enabled cell phone .
.
Take all components from the package
Headset / Charging Converter - USB charging cable (optional ) / Earhook /. User Guide
Charge your Headset
Before using you must charge the headset for approximately two hours when fully charged the battery
provides up to 6 hours of talk time and up to 200 hours of standby time.
1.
Plug the charger into the headset (See Picture B ). When the headset is charging, the red LED will light
2.
The red LED will turn oft after 60% charging. This indicated User can use this headset. However, it
needs to take two hours to fully charge the battery. Pull oft the charger after fully charged
Pair Headset to Cell Phone:
Pairing is the process of linking the headset with your Bluetooth enabled cell phone. The pairing process only
need to be done once for continuous usage. The headset can pairing with several cell phones, but only can use
with the cell phone that last pairing. Before you pair the headset, ensure that the battery is fully charged.
Pair Process:
1.
Press and hold the On/Off/Talk button for 15 seconds until the blue and red LED flash alternately.
Release the buttons. The headset is now in pairirig Mode.
2.
Initiate the device discovery feature on the cell phone and search for bluetooth device. Refer to the
cell phone User guide for relevant instructions.
3
. When prompted by the cell phone, enter the headset pin code 0000.
4.
When pairing is complete, the blue LED on the headset will flash at three second intervals and the
headset is now in standby mode, ready to make and receive call.
.
If disconnection or lost links occur,it may be due to the following reasons:
- The range over 20 feet between both headset and cell phone
- Cell phone disconnects the link in order to save power or for other purpose
- Either device is switched off
Cancel pairing Mode:
While in pairing mode, you can press and hold the TALK button for three seconds until both LED s turn
off to cancel the pairing prcccess.
Fit Headset to your ear
Headset is designed to fit comfortably in your ear. You can add the optional earhook to Ware more com-
fortably. You can ware the earhook either on left or right ear by adding the earhook in different directi-
ons. (See Picture. B)
Use the Headset after pairing
1.
Press and hold the Talk button until the blue light flashes. The headset is now in standby mode, ready
to make and receive calls.
2.
In standby mode, press and hold the Talk button until blue light turns off. The headset turns off
To telephone
To call over the mobile phone
Dial the call from your cell phone. The call is auto connected to your headset
Take on a call
When your cell phone rings, press the TALK button on your headset. The call is automatically connected
to your headset.
Indicator light
Volume ( + )
Volume ( - )
On-/Off-/Talk Button
Picture A
Picture B
Wireless Headset BH-2 V. 2.0
