C. Setting up using the learn function:
The learn function supplements the pre-
programmed code list. Whilst the standard
code list may provide the most necessary
functions, you can also add some additional
functions to your remote control. A new code
for a new original remote control can be
added, even if it is not in the code list.
In learn mode, you need the original remote
control whose codes you wish to store
in your Hama 8in1 Universal LCD Remote
Control.
Press the “LEARN” button to program the
commands. The “DELETE KEY” or “DELETE
ALL” functions for deleting the programmed
commands can be selected in the display us-
ing the arrow buttons. After confirming with
OK, “SURE DELETE” appears on the display.
After confirming once again, “SUCCESS”
appears. When “DELETE DEV” is selected, all
learned commands for the selected device
are deleted. When “DELETE ALL” is selected,
ALL learned commands for ALL devices are
deleted.
Learning commands
1. Press the button for the device where you
wish to save the commands (e.g. TV).
2. Press and hold the SET button for a little
over 3 seconds, then release it.
3. Using the
C
or
D
buttons, scroll until
“LEARNING” is displayed and press OK.
4. Using the
C
or
D
buttons, scroll until
“LEARN KEY” is displayed, then press OK.
5. Select the desired (target) button you wish
to program (e.g. power). “SELECT KEY”
appears in the display.
6. At a distance of approximately 30 mm,
point the transmitter of the original remote
control at the receiver window of the
Hama 8in1 Universal LCD Remote Control.
7. Press and hold the button (e.g. power) of
the original remote control for about 1
second until “SUCCESS” appears in the
display. If “FAILED” appears in the display,
then repeat steps 4 to 6.
8. Repeat steps 4 to 6 to program further
buttons.
Note:
1. A selected target button can learn several
source buttons. The Hama 8in1 Universal
LCD Remote Control only stores the last
programmed signal.
2. You can program all normal function but-
tons, with the exception of the SCAN and
MACRO buttons.
3. It may not be possible for some codes to
be learned by this remote control (due to
material cost limits).
4. Around 100 commands can be learned for 8
device buttons.
Deleting the button programming
To delete a programmed command, carry out
the following steps:
1. Press the button for the device where you
wish to delete a command (e.g. TV).
2. Press and hold the SET button for a little
over 3 seconds, then release it.
3. Using the
C
or
D
buttons, scroll until
“LEARNING” is displayed and press OK.
“LEARN KEY” now appears on the display.
4. Using the
C
or
D
buttons, scroll until
“DELETE KEY” is displayed, then confirm
with OK.
5. Press the button you wish to delete on the
Hama 8in1 Universal LCD Remote Control.
“SURE DELETE” appears on the display.
Confirm by pressing the OK button. “SUC-
CESS” appears in the display.
6. Repeat step 4 to delete the next button.
7. After you have deleted the required com-
mands, press a device button (e.g. TV) to
exit the deletion process.
15
14
Note:
1. To start again, press the EXIT button or the
device button (e.g. TV, VCR).
2. When carrying out the button test, aim the
remote control at the device you wish to
use.
3. The
CDA B
OK and EXIT buttons can
also only be used for programming during
the programming procedure. These but-
tons have no menu functions at this time.
4. If the device lock is active, then it must be
deactivated before a new configuration is
made.
B. Setting up using manual search:
If configuration using brand names and
codes was unsuccessful (or your brand
name cannot be found on the remote control
display), then you can also search for a suit-
able code for your device using the manual
search function.
1. Switch on the device you wish to operate
(e.g. TV). Insert a cassette if you wish to
operate a VCR.
2. Press and hold the SET button on the
remote control for a little over 3 seconds
until CODE SETUP appears on the display.
Press OK.
3. Using the
C
or
D
buttons, select the “DEV
SEARCH” menu item in the display and
confirm by pressing the OK button.
4. “SAT” (device search) flashes on the
screen (for example). Now select and
press a device button (TV, SAT, VCR,
DVD, CD, TAPE, AUX). Confirm the device
selection using the OK button. The cor-
responding device button then starts to
flash in intervals. The code also changes
according to the interval. Please interrupt
this interval using the
C
or
D
button. Now
access the lowest code value using the
arrow buttons.
5. Check the functionality of the remote con-
trol by pressing the standby button for one
second (red button). If the device remains
switched on, then the selected code has
no function.
Try again with the next available code
(using the
C
or
D
buttons).
Remember to check each individual code
with the red standby button.
6. If the device switches to standby mode,
then the code is most likely suitable for
use. Press the OK button to store the code.
“SUCCESS” then appears on the display,
followed by “DEV SUCCESS”. You can
now press the device button (e.g. DVD)
to exit the configuration or select further
configurations using the
C
or
D
buttons.
You can always go back one step until the
starting point by pressing “EXIT”.
7. After switching on the device again, check
whether the other functions (e.g. volume
or switching stations) also work when
using the same code.
If this is not the case, then try again with a
different code (steps 1 to 6).
Note:
1. If the search was not ended in time after
the device has reacted, then you can go
back to the corresponding code using the
arrow buttons.
2. The
C
and
D
, OK and EXIT buttons can
also only be used for configuration whilst
the search is running. These buttons have
no menu functions at this time.
3. When all codes have been searched,
the remote control finishes on the first
searched code.
If the device is locked, then unlock it
before the configuration is made.
