background image

 

P29 Instruction Manual 

 

16 

8.3 Warning 

Use this menu item to set the warning values. The first menu item that appears here is Select 
Warning Message (1 or 2). The settings for this warning message should then be changed. 
Use the “^” and “>” keys to select the number of the warning and press Enter to move to that 
warning's menu. 
The following sub-menu items are available: 

 Value 

 Hysteresis 

 TV 

 Warning 

signal 

 Mode 

8.3.1 Value 

This item adjusts the pressure value at which the particular warning should be activated. The 
pressure range defined by the scale can be used as the setting range. Select the pressure 
unit set for the display as the unit. If the volumetric flow, mass flow or flow rate (root-
extracted display) is displayed, select the Pa unit. 

8.3.2 Hysteresis 

This item can be used to select the hysteresis for the particular warning. The action 
described in 7.3.1 applies to the entry unit. The hysteresis is always positive. 

8.3.3 TV delay time 

The entry value of the warning is derived from the unfiltered pressure value. With this 
parameter, you can now specify how long the pressure value can be exceeded or not met 
until the warning is activated. The adjustment is done in ms. 25 ms is specified as the 
minimum value. 

8.3.4 Warning signal 

A warning signal sounds once every second when a threshold value is exceeded. With this 
parameter, you can set the duration of this warning signal for each warning. The maximum 
value here is 1000 ms (continuous tone). If both warnings are active, the longer warning 
signal of the two sounds. The warning signal may sound different depending on the 
activation level. A warning signal duration of 0 ms switches the signal off. 

8.3.5 Mode 

This item can be used to adjust whether the warning is to be activated when the pressure 
exceeds or falls below the warning pressure threshold. This affects the processing of the 
hysteresis value. 

Summary of Contents for P29
























Reviews: