background image

OVLERWSI_NF    OVLERWSI_WF

1000002450  (Rev. C - 06/16

Page 1

Review these instructions before beginning installation. Be sure that installation 
conforms to all plumbing, electrical and other applicable codes.

When installation is complete, ensure these instructions are left in the plastic bag 
provided inside the installed unit for future reference.

Service to be performed by authorized service personnel only.

INSTALLER

NOTE:  It is common practice to ground electrical hardware such as telephones, computers and other devices 

to available water lines. This can, however, cause electrical feedback in the plumbing circuit, which 

results in an “electrolysis” effect occurring in the fountain. This may result in water which has a 

metallic taste to it or has a noticeable increase in the metallic content of the water.

When inspecting plumbing circuit, remember the line may be grounded some distance from the 

installation, and may occur outside the building or area in which the unit is being installed.

This condition can be avoided (in most cases) by using recommended materials during installation. 

Any drain fittings provided by the installer should be made of 

plastic

 which will 

electronically isolate

 

the fountain from the remainder of the building’s plumbing circuits.

HTHB-OVLER-I

HTHBWF-OVLER-I

Halsey Taylor Owners Manual

OVL

 Fountains with Dual-Stream Bubbler

and HydroBoost

 Bottle Filler

WWW.RESTROOMDIRECT.COM      704•937•2673     129 Oak Park Dr., Unit A, Mooresville, NC 28115

Summary of Contents for OVL HTHBWF-OVLER-I









Reviews: