background image

Page 7

1000002478  (Rev. D - 09/18)

HAC8FSCWSNFQ_2F

Replacement Parts: 230V Parts List

*Includes Relay & Overload. If under Warranty, replace with same Compressor used 

in original assembly.

NOTE: All correspondence pertaining to any of the above water cooler or orders for 

repair parts MUST include Model number and Serial number of cooler, name and part 

number of replacement part.

Replacement Parts: Bottle Filler Parts List

Item No.

NS

NS

NS

NS

34

NS

NS

NS

NS

Part No.

98631C

98544C

1000004574

98546C

98666C

98549C

98551C

98552C

1000001813

Description

Kit - Electrical Package (220V)

Kit - IR Sensor

Kit - BF Solenoid Valve Replacement 220V

Kit - Aerator Replacement

Kit - Top Cover Replacement

Kit - Hardware & Waterway Parts

Kit - Filter Mounting Cover

Kit - Retro Filter Mounting

Kit - Tower/Basin Gasket

24

13

14

22

2

10

14

14

6

19

25

17

14

30

12

17

14

22

4

16

32

20

31

23

3

33

18

COOLER BACK

HANGER BRACKET

Figure 14

1

2

3

4

5

*6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

35

36

NS

22897C

23003C

28551C

0000001338

36208C

1000002147

98537C

98895C

98789C

98732C

55931C

0000000245

56092C

98899C

55996C

98533C

98776C

66703C

98777C

98778C

1000001812

1000001889

98773C

98724C

98751C

70935C

28123C

28124C

28127C

28128C

28705C

28706C

28144C

28525C

28148C

28528C

1000002062

1000001602

35826C

35827C

22844C

22955C

Panel - Bottom Dispenser

Bracket - Regulator Mounting

Hanger Bracket

Basin - Stainless Steel

Power Cord

Compressor Serv. Pak (220V/50Hz)

Kit - Pushbar/Pivot Blocks/Bumpers

Kit - Pushbars/Inserts/Nuts

Kit - Pushbar Bracket/Screws

Kit - Regulator - Green Spring

Cover-Dispenser Bottom

Kit - Fan Motor Assy/Blade/MotorShroud/Screws/Nut

Tubing - Poly  (Cut To Length)

Kit - Hardware

Strainer (See "General Instructions")

Kit - Bubbler/Nipple/Gasket

Kit - Condenser/Drier

Drier

Kit - Compr Mtg Hdwe/Grommets/Clips/Studs

Kit - Heat Exchanger/Drier

Kit - Bottle Filler Drain

Kit - Drain/Plate/Plug/Elbow/Nut

Kit - Cold Control/Screws

Kit - Evaporator Assembly

Kit - Relay/OverLoad/Cover (220V/50Hz)

Screw - Shoulder x 1/2" Lg.

Panel - Right Side (PV)

Panel - Right Side (SS)

Panel - Left Side (PV)

Panel - Left Side (SS)

Panel - Front Push (PV)

Panel - Front Push (SS)

Panel - Right Rear (PV)

Panel - Right Rear (SS)

Panel - Left Rear (PV)

Panel - Left Rear (SS)

Tee - 1/4 x 1/4 x 3/8 (3 Pack)

Kit - 75583C Elbow 5/16” - 1/4” (3 Pack)

Inlet Power

Internal Power Cord

Panel - Front Lower (PV)

Panel - Front Lower (SS)

ITEM 

NO.

PART NO

DESCRIPTION

Figure 13

2222 CAMDEN COURT

OAK BROOK, IL 60523

630.574.3500

FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR VISIT OUR WEBSITE 

WWW.HALSEYTAYLOR.COM

Summary of Contents for HTHBHAC8SS-NF-25








Reviews: