Halogen D20 Installation Manual Download Page 23

 

 
Copyright © 2023 Halogen Systems, Inc. All rights reserved worldwide. 

19

 

Limited Warranty

 

Halogen Systems warrants its products to the original purchaser against any defects that are due to faulty 
material or workmanship for a period of one year from date of shipment unless otherwise noted in the product 
manual. 

In the event that a defect is discovered during the warranty period, Halogen Systems agrees that, at its 
discretion, it will repair or replace the defective product or refund the purchase price excluding original shipping 
and handling charges. Any product repaired or replaced under this warranty will be warranted only for the 
remainder of the original product warranty period. 

This warranty does not apply to consumable products such as chemical reagents; or consumable components of 
a product, such as, but not limited to, lamps and tubing. 

Contact Halogen Systems or your distributor to initiate warranty support. Products may not be returned without 
authorization from Halogen Systems. 

Limitations 

This warranty does not cover: 

 

Damage caused by acts of God, natural disasters, labor unrest, acts of war (declared or undeclared), 
terrorism, civil strife, or acts of any governmental jurisdiction 

 

Damage caused by misuse, neglect, accident, or improper application or installation 

 

Damage caused by any repair or attempted repair not authorized by the Halogen Systems 

 

Any product not used in accordance with the instructions furnished by the Halogen Systems 

 

Freight charges to return merchandise to the Halogen Systems 

 

Freight charges on expedited or express shipment of warranted parts or products 

 

Travel fees associated with on-site warranty repair 

This warranty contains the sole express warranty made by Halogen Systems in connection with its products. All 
implied warranties, including, without limitation, the warranties of merchantability and fitness for a particular 
purpose, are expressly disclaimed. 

Some states within the United States do not allow the disclaimer of implied warranties, and if this is true in your 
state, the above limitation may not apply to you. This warranty gives you specific rights, and you may also have 
other rights that vary from state to state. 

This warranty constitutes the final, complete, and exclusive statement of warranty terms, and no person is 
authorized to make any other warranties or representations on behalf of Halogen Systems. 

Limitation of Remedies 

 The remedies of repair, replacement, or refund of the purchase price as stated above, are the exclusive 
remedies for the breach of this warranty. On the basis of strict liability or under any other legal theory, in no 
event shall Halogen Systems be liable for any incidental or consequential damages of any kind for breach of 
warranty or negligence. 

Subject to all terms and conditions 

www.halogensys.com/information

. 

 

 

 

Summary of Contents for D20

























Reviews: