background image

2021.05.25 

• 

REV. 3 

• MASS FLOW METER OPERATING MANUAL

 15

Sensor Setup

MENU 

 SETUP 

 Sensor

Choosing Engineering Units

SETUP 

 Sensor 

 Engineering Units

Changing device engineering units alters both the display and the data frame. Choose the 

parameter whose unit you want to change, and then select your desired engineering unit, 

confirming the change on the last screen.

Defining STP/NTP Reference Values

SETUP 

 Sensor 

 STP Flow Ref 

or

 NTP Flow Ref

Standardized flow rates are reported in “standard” or “normal” volumetric flow units that 

reference a given temperature and pressure combination. This reference is called STP 

(standard temperature and pressure) or NTP (normal temperature and pressure). Depending 

on the engineering units selected, either STP or NTP will be editable from this menu.

Reference options:

• 

Stan T

: Standard Temperature

• 

Stan P

: Standard Pressure

• 

Norm T

: Normal Temperature

• 

Norm P

: Normal Pressure

• 

Ref temp units

 changes the temperature units used for STP and NTP calculations. 

• 

Ref pressure units 

changes the pressure units used for STP and NTP calculations

Unless otherwise requested, your flow meter ships with a default STP of 25°C and 1 atm 

(which affects flow units beginning with “S”), and an NTP of 0°C and 1 atm (which affects 

flow units beginning with “N”).

 !

 Warning: 

Changes to STP or NTP references will alter your mass flow readings.  

Flow and Pressure Averaging

SETUP 

 Sensor 

 Flow Averaging

SETUP 

 Sensor 

 Pressure Averaging

Averaging the flow and pressure over a longer time may be useful in smoothing fluctuating 

readings. This menu changes the time constants of the geometric running averages for 

flow and pressure. Values roughly correspond to the time constant (in milliseconds) of the 

averaged values. Higher numbers generate a greater smoothing effect, to a maximum of 

255 ms.

Zero Band

SETUP 

 Sensor 

 Zero Band

T

he zero band threshold is an amount of flow under which flow values are displayed as 0. 

The maximum zero band is 6.38%. This function also applies to gauge pressure readings 

when using the optional barometer. For example, a 20 SLPM meter with a zero band value 

of 0.25% would display all readings below 0.05 SLPM as 0 SLPM.

 

The 

sensor setup menu

.

The 

engineering units menu

 

(

page 11

).

Adjusting the flow averaging time 

constant.

Configuring the zero band.

Summary of Contents for ALICAT SCIENTIFIC M































Reviews: