Haldex S-ABA Service Manual Download Page 16

  

13 

Frequently Asked Questions (cont’d)

Additional Information Available

15. Can I use moly lube with the Haldex
 

automatic brake adjuster?

 

No. A high concentration of moly-disulfide can

 

lower the friction capabilities in the adjusting

 

clutch parts and decrease automatic adjustment

 reliability.

16. Can I purchase anchor bracket wear
 

items separately (ie. anchor stud pins,

 

wear bushings)?

 

Yes. Normal wear items like anchor stud pins 

 

and wear bushings are available. Refer to the

 

Haldex Parts and Cross Reference Guide

 

L00090. Otherwise, contact Haldex Technical

 

Assistance for the appropriate bracket kit at

 1-800-643-2374.

Additional parts and service information on Haldex Automatic Brake Adjusters may be 
found in the following materials: 
 

Service Information 

 Installation and Maintenance Wall Chart  ..................................................................L60047 
 Service Manual (Truck/Trailer) ......................................................................................L30037 
 Installation Tips — Automatic Brake Adjuster (Pocket Size) ......................................L20397 

 

Parts Information 

 Parts and Cross Reference Guide (Truck/Trailer)  ........................................................L00090 
 Supplemental Automatic Brake Adjuster Kits  ...........................................................L20447 

These materials are readily available on the Haldex website 

haldex.com

, or you may        

order copies by contacting your Customer Service Representative at 1-800-643-2374.  

17. Does the control arm need to  be
 

properly set and secured?

 

Yes. Without proper placement and attachment,

 

the adjuster will not function properly. Make 

 

sure the control arm, anchor bracket and wear

 

items are in good working order to assure the

 

adjuster will operate as designed.

18. If automatic adjustment stops, can
 

I operate as a manual brake adjuster?

 

No. Completely check out foundation brake and

 

adjuster to determine cause of problem. Repair

 

or replace as needed to restore automatic

 adjustment.

Summary of Contents for S-ABA





















Reviews: