HAKO Jonas 1200 V, Instruction Manual

Page: 14 / 68

14
First Operation
2 First Operation
2.1 Instruction
Instruction is required before first ope-
ration. First instruction into handling of
the machine must be held by a qualified
person sent by your local Hako contract
dealer. Your Hako dealer will be infor-
med by the manufacturer upon delivery
of the vehicle and will contact you to
make a date for instruction.
2.2 Initial charging procedure
Before first operation of the
machine, fully charge the bat-
tery with an initial charging pro-
cedure and comply with the
operating instructions of the
charger as well as with those of
the battery manufacturer.
Hako cannot be held liable for
damages resulting from the
fact that the initial charging has
not or insufficiently been done.
2.3 Before Taking into Operation
Proceed to the following inspections be-
fore taking the machine into operation:
1. Check parking site for signs of leaka-
ge. Hoses, lines and tanks must be
free from any leakage or damage.
2. Open seat hood.
3. Check fuel level and refill if required.
4. Check engine oil level.
5. Close seat hood.
2.4 Start Machine
Before starting the machine
you are advised to read and
comply with the Provisions of
Operating from Safety Infor-
mation chapter!
Before starting the machine, subse-
quently ac-tuate the following control
elements:
1. Set all operating levers and switches
to neutral.
2. Secure the vehicle by engaging the
parking brake.
3. Turn ignition key to switch on igniti-
on.
4. Hako-Jonas 1200 V:
Actuate choke (with cold engine on-
ly).
Hako-Jonas 1200 D:
Preheat until control lamp extinguis-
hes.
5. Continue turning ignition key clock-
wise to start engine.
- After the motor has started, the en-
gine oil pressure and charge status
lamps have to extinguish.
Do not use the Hako-Jonas
1200 V/D at ambient tempera-
tures of more than 40°C.
Do not start the machine at
temperatures of -15°C or less.
Liquid propellant gas system:
refer to LPG operating instruc-
tions.
Its not possible to start the ma-
chine, when the accelerator
pedal is linked.
If the starting procedure has to
be repeated or if the engine
stops, re-starting is possible
only after ignition has been tur-
ned off. The ignition lock is
equipped with a protection to
preclude repeated ignition with
the engine running.
Interruption of the starting pro-
cedure ofter 10 seconds and
brief pause between starting
14
First Operation
2 First Operation
2.1 Instruction
Instruction is required before first ope-
ration. First instruction into handling of
the machine must be held by a qualified
person sent by your local Hako contract
dealer. Your Hako dealer will be infor-
med by the manufacturer upon delivery
of the vehicle and will contact you to
make a date for instruction.
2.2 Initial charging procedure
Before first operation of the
machine, fully charge the bat-
tery with an initial charging pro-
cedure and comply with the
operating instructions of the
charger as well as with those of
the battery manufacturer.
Hako cannot be held liable for
damages resulting from the
fact that the initial charging has
not or insufficiently been done.
2.3 Before Taking into Operation
Proceed to the following inspections be-
fore taking the machine into operation:
1. Check parking site for signs of leaka-
ge. Hoses, lines and tanks must be
free from any leakage or damage.
2. Open seat hood.
3. Check fuel level and refill if required.
4. Check engine oil level.
5. Close seat hood.
2.4 Start Machine
Before starting the machine
you are advised to read and
comply with the Provisions of
Operating from Safety Infor-
mation chapter!
Before starting the machine, subse-
quently ac-tuate the following control
elements:
1. Set all operating levers and switches
to neutral.
2. Secure the vehicle by engaging the
parking brake.
3. Turn ignition key to switch on igniti-
on.
4. Hako-Jonas 1200 V:
Actuate choke (with cold engine on-
ly).
Hako-Jonas 1200 D:
Preheat until control lamp extinguis-
hes.
5. Continue turning ignition key clock-
wise to start engine.
- After the motor has started, the en-
gine oil pressure and charge status
lamps have to extinguish.
Do not use the Hako-Jonas
1200 V/D at ambient tempera-
tures of more than 40°C.
Do not start the machine at
temperatures of -15°C or less.
Liquid propellant gas system:
refer to LPG operating instruc-
tions.
Its not possible to start the ma-
chine, when the accelerator
pedal is linked.
If the starting procedure has to
be repeated or if the engine
stops, re-starting is possible
only after ignition has been tur-
ned off. The ignition lock is
equipped with a protection to
preclude repeated ignition with
the engine running.
Interruption of the starting pro-
cedure ofter 10 seconds and
brief pause between starting