background image

13

●    

: Auto shutoff on/off setting

When the auto shutoff function is set to on and no operation is performed for 30 minutes (Initial 

value) after the iron is set in the iron holder, the buzzer sounds and the auto shutoff function will be 

enabled. Leaving the iron in the iron holder as it is, the buzzer sounds every 30 minutes.

1.  In the auto shutoff setting mode, either               or              is displayed.
 

   

  : The auto shutoff function is off, regardless of the auto sleep functioin set time.

 

   

  : The auto shutoff function is on, and the auto shutoff time is activated.

2.               and              will be switched alternately if you press the

  

 (

  

 ) button.

3. The display will return to              if you press the

  

 button after selecting.

  

 

: Auto sleep temperature setting

Sets the auto sleep temperature. Setting a high sleep temperature enables shorter start up time 

when the unit recovers from sleep mode.

NOTE: 

High-power mode is mainly suited to applications that require large heat capacity such as 

quick soldering of ground patterns or cast metal products.

●    

: Power-mode setting

1.  In the Power-mode setting mode, either               or              is displayed.
 

   

  : Selects high output.

 

   

  : Selects normal output.

2.               and              will be switched alternately if you press the

  

 (

  

 ) button.

3. The display will return to              if you press the

  

 button after selecting.

  

CAUTION

If the tip is overloaded, it may cause overshooting.

  

CAUTION

Setting the sleep temperature too high will shorten tip life.

Auto sleep temperature setting range : for Celsius: 200 to 300ºC

for Fahrenheit: 390 to 580ºF

1.  When the unit enters auto sleep temperature setting mode, the hundreds digit starts flashing. Once 

the unit starts flashing, enter a desired value within the auto sleep temperature setting range.

2.  If the entered value exceeds the auto sleep temperature setting range (see box on the left below), 

the hundreds digit starts flashing again. If this happens, enter a correct value.

3. The display will return to              if you press the

  

 button after selecting.

Summary of Contents for FX?801























Reviews: