background image

Unit

mm

Figure 1

NET DIMENSION

INSTALLATION AND ACCESSORY PARTS

7

686   

686 

 

1

1

1

5

  

 

       The largest allowed slope of the shank base of the machine is 2

. The slanting or rough ground will 

result in unstable running or stoppage of the machine. Please adjust it with following methods:

Confirm it's horizontal 

Hang the plumb  to confirm it's horizontal.

Adjust the adjustable feet

1)  To twist the adjustable  foot, please  first lift up 
      the side of the foot slightly, and twist the foot.
2)  Fasten the nut after adjustment.

Adjust the Installation position  

High

Low

Adjustable foot

<2 

Install the drain hose

Outer drain hose

 component

Drain hose hook

Drain  hose joint

Drain hose clamp

       First install the drain hose hook on the parts of 
outer drain hose component.

       Put the drain hose clamp on the outer drain hose,
insert the outer drain hose into the joint for it, and
then clutch tightly with drain hose clamp.

Please  install and adjust the machine according to the requirement of  the manual. 
It  is very  important  to your security  and  correct operating  the machine.

Summary of Contents for HLT20E
















Reviews: