background image

10

MAINTENANCE SERVICE AND TROUBLE SHOOTING

     If you replace the computer sequencer without checking the other components carefully, the 
computer sequencer may be damaged again. Therefore, please first check if the other components 
working normally before replacing the sequencer in maintenance.

No washing and No water filling

C

Trouble-shooting charts 

    

Replace the sequencer

Replace the power cord

Replace the door switch

Repair or replace the wire unit

Check the transmission system.

Replace the motor

Repair the capacity

Repair or replace the wire unit

Pull out  the power cord

Replace the water inlet valve

Confirm that there's no power failure,  pull the
 power plug out and insert it tightly again. Then 
close the top lid , turn the sequencer knob to the 
wash location and pull it out

Measure the voltage of  

white & black wires of the two ends of the power 

input of the sequencer

Measure the voltage of  

 the two ends of the power cord

Measure the voltage of  

 the door switch with the top lid 

close

Insert the 

plug and measure the voltage of  

two ends of the motor  

Check if the wire unit is normal?

Check if the capacity is normal?

Check if the motor  is action?

Measure the voltage of  

the two ends of the water inlet valve

Yes

No

Infinite

No

No

Yes

No

Yes

No

No

Yes

Yes

Yes

Yes

No

The resistance is 0

Summary of Contents for HLT20E
















Reviews: