Display board
1
Signal receiver
2
Setting temp.display
1
2
Actual inlet grille may vary from the one shown in the
manual according to the product purchased
Indoor Unit
Inlet
Display board
(inside)
Inlet grille
Outlet
ON/OFF
Button
Air Purifying Filter Vertical blade
(inside)
(adjust left and
right air flow)
Horizontal flap
(adjust up and down air flow
Don't adjust it manually)
Outdoor Unit
4
OUTLET
CONNECTING PIPING AND ELECTRICAL WIRING
DRAIN HOSE
INLET
Please be subject to the actual produce purchased the
above picture is just from your reference
Loading of the battery
1
2
3
4
Parts and Functions
Remote controller
1
6
8. Additional functions display
Supplemented
2
Operation mode
QUIET SLEEP electrical
HEALTH TURBO
heating
7
Remote controller
3
4
5
8
9
18
10
11
19
20
12
SWING
SWING
21
13
22
14
23
15
24
16
17
25
1. Mode display
Function: Sleeping---- Healthy
airflow position1--- Healthy airflow
position2--- standard position
--- Turbo
--- Air sending --- A-B yard--- AUTO
--- 10
o
C
Heating
Operation mode
AUTO COOL DRY
FAN
HEAT
Remote controller
Display
circulated
LOW
MED
HI
AUTO
9. QUIET button
10. HEAT button
11. COOL button
12. SWING LEFT/RIGHT button
13. FAN SPEED button
14. TIMER button
15. HEALTH button
16. LOCK button
Used to lock buttons and LCD display
17. LIGHT button
Control the lightening and extinguishing
of the indoor LED display board.
18. POWER ON/OFF button
19. DRY button
20. TEMP button
21. SWING UP/DOWN button
22. HOUR button
23. EXTRA FUNCTION button
2. Signal sending display
3. SWING display
4. FAN SPEED display
24.CANCEL/CONFIRM button
Function: Setting and cancel to the
timer and other additional functions.
25. RESET button
When the remote controller appears
abnormal, use a sharp pointed
article to press this button to reset
the remote.
5. LOCK display
6. TIMER OFF display
TIMER ON display
7. TEMP display
Remove the battery cover;
Load the batteries as illustrated.
2 R-03 batteries, resetting key
(cylinder);
Be sure that the loading
is in line with th
e" + "/"-";
Load the battery,then put on the cover again.
The distance between the signal transmission head and the rece-
iver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change- over
wireless telephone is installed in the
ver is apt to be disturbed in receiving the signals,
so the distance to the indoor unit should be shorter.
type fluorescent lamp or
room, the recei
Note:
Full display or unclear display during operation indicates the
ries have been used up. Please change batteries.
If the remote controller can't run normally during operation, please
reload several minutes later.
batte
remove the batteries and
Hint:
Remove the batteries in case won't be in use for a long period. If
there is any display after taking-out, just press reset key.
2
Summary of Contents for HAS12FAAIN
