background image

LITERATURE: LIT-WMMS-(58) (2)-DC IVTR-1 to 1-C8-II-20131029

INSTALLATION INSTRUCTION 

Wall Mount Mini Split Systems

Literature Part No: 

Subject to Continuous Engineering Change and Product Improvement without Prior Notice.

LIT-WMMS-(58) (2)-DC IVTR-1 to 1-C8-II-20131029

16~22 SEER

DC INVERTER R410A-SYMPHONY SOLO

Single Zone (58) (2)

Cooling and Heat Pump

09~36k

YMGI Group

, POB 1559

YMGI Group New Energy

, POB 1668

O'Fallon, MO 63366, USA

Tel:(866)833-3138  Fax:(866)377-3355

Web Site: www.ymgigroup.com

Email: [email protected]

This product is designed and manufactured

 

free from defects in material and workmanship for normal use and maintenance.

Installation, operation, maintenance and service shall follow professional practices for regular cooling and heating equipment, 
NEC, State, City or Local Codes and related manuals from YMGI. Otherwise, damage to equipment or property and even 
injury to people may occur.

Installer

: Currently licensed HVAC technician only. Read manual before installation. Fully fill in warranty registration card.

User

: Keep this manual for future maintenance and service use.

Servicer

: Use this manual for service reference.

YMGI is the Trademark and Property of YMGI Group New Energy. Copyright of YMGI Group New 

.

Energy

YMGI, Engineered Comfort Products for A Sustainable and Efficient Green World !

Summary of Contents for WMMS-09C-V2A/B(58) 2





















Reviews: