Haier Ginesis HLF103Q Service Manual Download Page 11

C

3

-wire cord connections

3

8

Danger :

       Improper connection of the equipment grounding conductor can result in a risk of electrical shock.  Check with a
 licensed electrician if you are  in doubt  as to whether the appliance is properly  grounded.   The dryer MUST be connected 
to a grounded metal, permanent wiring system,  or an equipment grounding conductor must be run with the circuit conductors 
and connected to the equipment-grounding terminal or lead on the appliance.

1. Remove the screws securing the terminal block access cover 

and the strain relief mounting bracket located on the back of the 
dryer in the upper corner.

2. Install a strain relief into the power cord entry hole of the 

    mounting bracket. Finger tighten the nut only at this time.
3. Thread a 30 Amp. Power cord, 245 IEC66(YCW) 450V/750V,

    through the strain relief.
4. Attach the power cable earthconductor to the silver 

   coloured centre terminal on the terminal block. Tighten 

   the screw securely.

5. Attach the remaining two power cable outer conductors to the 

outer silver coloured terminals on the terminal block. Tighten both 
screws securely. Warning:Do not make a sharp bend or crimp
wiring/conductor at connections.

6. Reattach the strain relief mounting bracket to the back of the dryer 

    with two screws. Tighten screws securely.
7. Tighten the screws securing the cable restraint firmly against the 

    power cable.
8. Tighten the tension relief nut securely so that the tension relief 

    does not turn.
9. Reinstall the terminal block cover.

Grounding
instruction:

This appliances must be connected to a ground metal,permanent wiring system, or an equipment-grounding 

conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or 

lead on the appliance. 

nut

tighten nut
to these threads

power cord

strain relief
mounting bracket

N

L

Caution:

Label all wires prior to disconnection, when servicing controls.Wiring errors can cause improper operation 

and be dangerous. Check unit for proper operation after servicing.

Warning:

Discard or destroy the carton and plastic bags after the dryer is unpacked. Children should not be allowed to use 

them to play with. Cartons covered with rugs bedspreads, or plastic sheets can become an airtight chamber

and cause suffocation leading to death. Make all packing materials inaccessible to children.

Warning:

The instructions in this manual and all other literature included with this dryer can not cover every possible 

condition and situation that may occur. Good safety practice and caution must be applied 

when installing, operating and maintaining any appliances. After installing, if you are indoubt, 

call a qualified electrician to install and wire the dryer.

 Improper connection of the equipment-grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative or personnel if you are in doubt as to

whether the appliance is properly grounded.

Warning:

brass terminal

Summary of Contents for Ginesis HLF103Q















Reviews: