Haier GE GDF450P R0 Series Technical Service Manual Download Page 9

Page: 9 / 61

– 9 –

Operation and Cycle Information

This section of the guide provides details on segments of cycles, timing of cycles, temperature

expectations, and cycling of the heater during the dry portion of a cycle.

Auto Hot Start

At the beginning of the main wash, the dishwasher checks the temperature of the water, and if it is

below 90°F, then it will add up to 10 minutes of time to heat the water to 90°F by circulating the water

while the heater is on. Similarly, at the beginning of the final rinse, the dishwasher will check the water

temperature, and if it is below 105°F, then it will add up to 15 minutes of time to heat the water to 105°F.

Once it reaches the target temperature, any remaining hot start time will be truncated and will continue

on with the cycle.

The cycle chart below explains the segments of a cycle (cycles for all models included, but not all

models contain the same cycles). It details fill and drain times which depend on either a full or partial

drain. It provides the circulation time in each segment but does not include turbidity or temperature

adjustments or dry cycles (see the

Dry System

, under the

Tub

section in this guide). Times will vary

depending on turbidity response and incoming water temperature.

Cycle Option Selected

Light

Normal

Fixed Heavy 1-Hour Everyday

Heavy

Duty

All Zones

Options

143

140

209

Boost

Dry

191

247

164

Heated

Dry

141

207

124

Bottle

Wash

110

166

Temp

Boost

141

156

Sani-

Steam

185

176

Bottle

Wash

Boost

Dry

214

270

187

Temp

Boost

Dry

246

260

Sani-

Steam

Boost

Dry

290

280

Bottle

Wash

Heated

Dry

163

230

147

Temp

Boost

Heated

Dry

205

220

Sani-

Steam

Heated

Dry

250

240

Temp

Boost

Bottle

Wash

Boost

Dry

268

283

Sani-

Steam

Bottle

Wash

Boost

Dry

313

303

Sani-

Steam

Temp

Boost

Dry

290

280

Temp

Boost

Bottle

Wash

Heated

Dry

229

243

Sani-

Steam

Bottle

Wash

Heated

Dry

273

263

Sani-

Steam

Temp

Boost

Heated

Dry

250

240

Sani-

Steam

Temp

Boost

Bottle

Wash

Boost

Dry

313

303

Sani-

Steam

Temp

Boost

Bottle

Wash

Heated

Dry

273

263

Summary of Contents for GE GDF450P R0 Series






























































Search results

Summary of Contents for GE GDF450P R0 Series

Reviews:

Related manuals for GE GDF450P R0 Series

Brands by name

Popular brands

Haier GE GDF450P R0 Series, Technical Service Manual

Search results

Summary of Contents for GE GDF450P R0 Series

Reviews:

Related manuals for GE GDF450P R0 Series

Brands by name

Popular brands