Haier GE GDF450P R0 Series Technical Service Manual Download Page 55

Page: 55 / 61

– 55 –

To Exit Error Mode

Models with 1 or 2 pads, power cycle the unit.

Models with 3 or more pads, press any key.

Start LED

Blinks

Fault

Code

Fault Description

F153

Door latch failure.

F50

Temperature sensor

high.

F51

Temperature sensor

low.

F53

Fuse failure with

circulation pump on.

F56

Failure to drain.

F97

Absent heat source.

F112/

F155

Key stuck.

F99

Minimum wash

temperature not met.

To Enter Error Mode

Wake up the control by opening and closing the

door for all models.

For Models with 1 or 2 Pads

Wake up the control. Press and hold the Start

pad with the door closed, then open the door for

3-seconds, close the door and release the Start

pad. The Clean or Heavy light will turn on.

For Models with 3 or More Pads

Wake up the control. Press and hold the

furthest most pad on the left and the Start pad

simultaneously for 5 seconds.

Door Status Check

: On entry into Error Mode,

the control reports the door status for 10 seconds.

• All LED's are solidly illuminated, if the door is

detected as closed.

•

All LED's are flashing, if the door is detected

as open.

Error Code Display Mode

After the door check, the control will enter a

mode to display any fault codes that are currently

detected by the control.

Error Mode

Summary of Contents for GE GDF450P R0 Series






























































Search results

Summary of Contents for GE GDF450P R0 Series

Reviews:

Related manuals for GE GDF450P R0 Series

Brands by name

Popular brands

Haier GE GDF450P R0 Series, Technical Service Manual

Search results

Summary of Contents for GE GDF450P R0 Series

Reviews:

Related manuals for GE GDF450P R0 Series

Brands by name

Popular brands