Haier GE GDF450P R0 Series Technical Service Manual Download Page 57

Page: 57 / 61

– 57 –

Start LED

Blinks

SSD

Display

Error Name

Action Item

Adc or HrF Internal Board

Failure

Replace machine control board. Power cycle to

exit.

CFE

Continuous Fill

Error

Check for a stuck open water valve by

disconnecting power to the dishwasher. Check to

see if water valve is getting continuous voltage.

Ftd

Failure to Drain

Check for clog in air gap/disposer, drain hoses,

and drain pump. Check that disposer plug has

been removed. Check drain hose routing to match

Install Instruction.

H20

Water Supply

Failure

Verify the water supply line is connected properly,

the supply line valve is turned on, and restart the

cycle.

AcF

High Supply

Voltage

Check the supply voltage. Supply voltage is

greater than 170V.

dLF

Door Latch Failure

Check door latch for resistance between pin 1

(

dark blue

) and pin 3 (

yellow

) at the latch with

the door closed. Check continuity of the harness.

Check connector J603 to verify pin 1 and pin 2 has

no continuity. Power cycle to exit.

PrS

Pressure Sensor

Failure

Verify pressure sensor harness has continuity.

Unplug/plug harness at board and pressure sensor.

Replace pressure sensor if needed.

FuS

Board Circulation

Pump Fuse

Failure

Check the continuity on the circulation pump fuse.

Check the circulation pump motor.

Critical faults will shut the dishwasher down. The Start LED then will blink according to the fault. This

will be displayed to the consumer and will allow the technician to properly diagnose a critical issue

without having to enter Service Mode.

Critical Faults

Summary of Contents for GE GDF450P R0 Series






























































Search results

Summary of Contents for GE GDF450P R0 Series

Reviews:

Related manuals for GE GDF450P R0 Series

Brands by name

Popular brands

Haier GE GDF450P R0 Series, Technical Service Manual

Search results

Summary of Contents for GE GDF450P R0 Series

Reviews:

Related manuals for GE GDF450P R0 Series

Brands by name

Popular brands