Haier ESD 300 Series Service Manual Download Page 70

Page: 70 / 93

DIAGNOSTICS

Indicator Lamps

Water Heated (ESD310-311-312) Indicator glows only when the cycle pauses to heat water to a set temperature.
Washing or rinsing continues as the water is heated. Once water reaches the set temperature, the light goes off and
the cycle resumes.

Washing (ESD310-311-312) Indicator glows during the pre-wash and main wash periods.

Turbidity Sensor (ESD310-311-312) Indicator glows during the sensing part of the cycle. Washing continues during
the sensing.

Rinsing (ESD310-311-312) Indicator glows during the rise periods.

Drying (ESD310-311-312) Indictor glows during the drying cycle after the final rinse.

Clean Indicator glows when a wash cycle is complete and will remain ON until the door is opened.

Sanitized Indicator glows when the cycle has met sanitization conditions. The light will remain ON until the door is
opened.

Add Rinse Aid (ESD310-311-312) Indicates the Rinse Aid Dispenser is empty. The indicator glows while a cycle is running.

Summary of Contents for ESD 300 Series






























































































Search results

Summary of Contents for ESD 300 Series

Reviews:

Related manuals for ESD 300 Series

Brands by name

Popular brands

Haier ESD 300 Series, Service Manual

Search results

Summary of Contents for ESD 300 Series

Reviews:

Related manuals for ESD 300 Series

Brands by name

Popular brands