background image

 

 

 Model 410

 

Owner’s Manual 

6/24/2014 

Five-Button Controller 

 
This appliance features a five-button controller with 

an LCD display. The controller can be used to view 
the appliance’s status, perform regenerations, and 

change settings. An independent Hague dealer 
should set the Service Settings during installation of 
the appliance.  
 
 
 
 

Figure 1: Five-Button Controller

Controller Part 

Function 

LCD Display 

Shows the status of the controller; it is very important to know which mode the controller is in for 

proper operations 

Normal Operating 
Mode 

Shows some or all of the following depending on settings: 

 

The amount of soft water remaining until the next automatic regeneration  

 

The number of days until the next regeneration (in Mode 1) 

 

The flow rate in gallons per minute  

 

Whether the appliance will regenerate tonight (If the REGENERATE button has been 
pressed and released) 

 

Time of day 

Service Settings 

Mode 

Includes settings such as the language, mode, water hardness, and time of each regeneration 

step. Service Settings must be set before Customer Settings. Otherwise, some values may not be 

available. Service Settings Mode is intended for use by qualified service personnel 

Customer Setting 
Mode 

Includes setting the time of day, the regeneration time, and the number of people in the 
household; depending on the service settings, this option may not be available 

Water Flowing 

Indicator 

Indicates that water is flowing through the appliance; useful for checking for proper plumbing and 

leaks

 

Soft Water 
Remaining  

Shows the gallons (or liters) of soft water remaining until the next automatic regeneration. 
Typically, each person in the household uses about 75 gallons (284 L) per day. 

Recharge/ 
Regeneration Status 

Shows regeneration cycle numbers during regeneration. When regeneration is complete, the 
display returns to the Normal Operating Mode (see above). Regeneration typically is complete in 

about 30 minutes.  

LCD Display 

Buttons 

WaterMizer 
Light 

Summary of Contents for Maximizer 410





































Reviews: