background image

7

A BDE

F G

struction, RF remote system 

Installation

o

  connect the power supply and 

the motor unit to the remote re-
ceiver. 2 different plug sizes 
make this connection only possi-
ble to make in the right way 

o

  after having connected the plugs, 

the blue light will be lit 

o

  push the emitter buttons and the 

motor unit will move up and 
down

o

  for stopping the motion one of 

the buttons need to be pushed 

Learning

o

  if the remote receiver does not respond when pushing the emitter buttons, reset the 

receiver. After that, code the emitter and receiver together again 

Coding

o

  push the learner button on the receiver for less than 1 sec. 

o

  push one of the emitter buttons 

o

  the red light will start flashing 

o

  push one of the emitter buttons again and the red light will turn off 

o

  the units now are coded together with a unique code 

Reset

o

  push and hold down the learner button on the receiver for 10 sec. (will be reset when 

the red light turns off). 

External rocker switch 

o

  the external rocker switch can be connected to the receiver, if a fixed operation unit is 

required.

Trouble shooting 

o

  check the plug connections 

o

  check whether the blue light is on 

o

  reset the receiver and make a new coding 

o

  always test the lift on the manual rocker switch 

o

  see www.venset.com , click “support” 

Summary of Contents for 421.68.44











Reviews: