Hafco WBS-1836 Instruction Manual Download Page 5 | Manualshive

Page: 5 / 29

background image

3

Thank you for choosing this Belt Sander. We are pleased to offer you our best machinery and
service, and trust that you will find our machinery economical, productive and easy to operate.

This manual covers the proper operation, safety and maintenance of the machine. It is important
that this manual be read in its entirety before operating the machine. Although the machine has
been checked and inspected in compliance with relevant safety regulations, the machine's safety
and best performance are dependent on proper maintenance and operation. Hazards that arise
due to improper operation and maintenance are solely the responsibility of the operator.

We thank you again for you choice, and for your careful reading of this manual.

PREFACE

Page 5

Instructions Manual for WBS-1836 (L124)

07/08/2017

«
...
3
4
5
6
7
...
»

Summary of Contents for WBS-1836






























Reviews:

No comments

Related manuals for WBS-1836

Brand: MIRKA Pages: 40

Brand: Road Xpedition Pages: 3

POWERPLUS POWC40100

Brand: VARO Pages: 7

Brand: hollu Pages: 44

Brand: Flex Pages: 228

Brand: Worx Pages: 120

Brand: TOOLCRAFT Pages: 60

Brand: Bauer Pages: 16

VITO PRO-POWER VILV250

Brand: Central Lobao Pages: 37

Brand: Sunex Tools Pages: 4

Brand: EINHELL Pages: 132

Brand: Lagler Pages: 68

Brand: Makino Pages: 568

Brand: Felisatti Pages: 24

Brand: Makita Pages: 8

Brand: Makita Pages: 16

Brand: Makita Pages: 44

Brand: Makita Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands