Hafco WBS-1836 Instruction Manual Download Page 13 | Manualshive

Page: 13 / 29

background image

11

Motor is electrified when sanding belt touched limit switch A/B, the motor (C) turns front and
reverse to control the roller swings.

Warning

: please don’t adjust dividing scale unless sanding belt swings unusually.

Figure5

If the conveyor belt runs to the right or left during operation, or the conveyor belt tension is
too loose or too tight, adjust it by turning the adjustment nuts on either side of the conveyor
table. The conveyor belt should run at the center of the conveyor table, and should be
tensioned so that there is good traction during stock feeding.

Figure6

ADJUSTING SANDING BELT TRACKING & TENSION

ADJUSTING CONVEYOR BELT TRACKING

Page 13

Instructions Manual for WBS-1836 (L124)

07/08/2017

«
...
11
12
13
14
15
...
»

Summary of Contents for WBS-1836






























Reviews:

No comments

Related manuals for WBS-1836

Brand: Kalorik Pages: 16

Brand: Shoe Systems Plus Pages: 18

Brand: SUHNER Pages: 40

Brand: WilTec Pages: 14

Brand: GMC Pages: 40

Brand: Casals Pages: 108

Brand: Sunex Pages: 11

Evolution NPE120-2

Brand: Nupower Pages: 68

Brand: Sparky Group Pages: 62

Brand: pro.point Pages: 32

Brand: Fakir Pages: 28

RANDOM ORBITAL SANDERS

Brand: 3M Pages: 5

PowerPlus POW4014

Brand: VARO Pages: 8

Brand: Grizzly Pages: 2

Brand: Feider Machines Pages: 15

Brand: CentralPneumatic Pages: 16

Brand: Parkside Pages: 56

Brand: Stanley Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands