background image

 

 

Safety instructions

 

 

This  appliance  can  be  used  by  children  aged  from  8 
years  and  above  and  persons  with  reduced  physical, 
sensory  or  mental  capabilities  or  lack  of  experience 
and knowledge if they have been given supervision or 
instruction  concerning  use  of  the  appliance  in  a  safe 
way and understand the hazards involved. 
 

 

Children  should  be  supervised  not  to  play  with  the 
appliance. 
 

 

Before using the equipment, assure that: 

  the tool can be pushed far enough into the chuck 

  (Test this with a dipstick and clean the handpiece, if 

necessary) 

  the  inserted  tool  sits  properly  in  the  chuck  and  will 

not cant/jam while clamping it 

  the  tool  is  approved  for  using  it  at  the  max  speed 

(see  manufacturer´s  instructions),  or  only  use  the 
speed required by the instrument 

  the tool is absolutely dry 

 

 

For  safety  reasons  do  not  change  the  tool  while  the 
motor is running. 

 

 

Switch off the unit immediately if:  

  the bur comes off during the treatment itself,  

  the motor blocks during the treatment. 

 

Summary of Contents for 0897

















Reviews: