10
5.52.180.00.01.07
5 Technical
data
Pos: 9.2.1 /1_HADEF/5--TECHNISCHE DATEN/Kettenzug/29/06/29/06E-Synchro @ 2\mod_1279522114323_52.docx @ 14788 @ @ 1
Capacity
kg 500 1000
2000
2500
3200
hoisting unit
AK 4
AK 4
AK 6
AK 7
AK 7
Number of chain falls
2 2
2
2
2
FEM 9.511/ ISO 4301
2m/ M5
2m/ M5
2m/ M5
2m/ M5
2m/ M5
load chain
mm 5x15 5x15
7x21
9x27
9x27
load bar 1N
for beam flange width 2N
from - to 3N
mm
mm
mm
74-150
151-220
221-310
74-150
151-220
221-310
82-156
157-210
211-306
106-223
224-310
-
106-223
224-310
-
lifting speed approx.
m/min
9/2,2
8/2
11/2,6
8/2
hoist motor output
kW 2x0,88/0,18
2x0,88/0,18
2x1,8/0,44 2x4/1,1 2x4/1,1
operating mode S 3
%
ED
60/40 60/40 60/40 80/50 80/80
travel speed approx.
m/min
16/4 16/4 16/4 16/4 16/4
trolley motor output
kW 0,25/0,06 0,25/0,06 0,25/0,06 0,25/0,06 0,25/0,06
operating mode S 3
% ED
40/40 40/40 40/40 40/40 40/40
travel path when reeling off 30 m
of hand chain
m
7,8
7,8 9,8 6,3 6,3
hand chain pull for travel approx.
N 70 90 130 80 100
noise emission at
1m distance
tolerance +2 dB(A)
dB(A)
65 65 70 70 70
max. wheel load approx.
at 3 m suspension height
kg
180
310 640 785 985
weight at 3 m track height
approx.
kg
120
128 205 255 255
Pos: 9.3 /1_HADEF/5--TECHNISCHE DATEN/Allgemein/E-Motor/400V Motor @ 3\mod_1378727800377_52.docx @ 27382 @ @ 1
3-phase current motor 400V/50Hz - IP55 – F – max. 1000 m above sea level.
Order-related Special data, refer to the motor nameplate.
Pos: 10.1 /1_HADEF/6--MONTAGE/*Ü1*/#. Kapitel - Montage @ 0\mod_1172127582099_52.docx @ 255 @ @ 1
6 Installation
Pos: 10.2.1 /1_HADEF/6--MONTAGE/Allgemein/01.Alle Hebezeuge @ 0\mod_1182334877463_52.docx @ 6265 @ @ 1
The assembly and installation depends on the local environment. The hoist must be suspended in a way that
it can position itself freely.
Pos: 10.2.2 /1_HADEF/6--MONTAGE/Allgemein/02.auf Träger - allgemein @ 0\mod_1172220892763_52.docx @ 270 @ @ 1
6.1 Trolley
For assembly on a beam a travel limit must be placed at either end of the track.
This must be attached so that any elastic limitation buffer or the trolley wheels are driven against them in
their end position when moving.
Generally, additional lifting gear (e.g. fork lift, lifting platforms) will be required for the assembly. These must
take the weight of the devices securely.
Pos: 10.3.1 /1_HADEF/6--MONTAGE/Kettenzug/29/06+91/09/01.Allgemein @ 0\mod_1184740001750_52.docx @ 6766 @ @ 1
For hoists up to 6,3t capacity the trolley and the bottom block can be adjusted to different beam flange
widths.
Hoists from 8t capacity up are supplied adjusted to a fixed beam flange width in the factory. The adjustment
of the bottom block cannot be changed afterwards.
Pos: null /1_HADEF/---ALLGEMEIN/Hinweise/Kettenzüge/VORSICHT - Maß X = 2-3mm @ 0\mod_1177323497964_52.docx @ 5160 @ @ 1
CAUTION!
The distance "X" between the wheel flanges of the trolley wheels must exceed the flange width "B" of the
beam by 2-3 mm (1-1,5 mm each side).
Pos: 10.3.3 /1_HADEF/6--MONTAGE/Kettenzug/29/06+91/09/02.Einstellung X, Montage bis 6,3t @ 0\mod_1184740487268_52.docx @ 6771 @ @ 1