background image

Table 2  Troubleshooting table (continued)

Problem

Possible cause

Solution

Sampler does not have
sufficient lift.

Strainer is not completely
submerged.

Install the shallow depth strainer
(2071 or 4652).

Intake tube has a leak.

Replace the intake tube.

Pump tube is worn.

Replace the pump tubing

on page 21.

Pump roller assembly is worn.

Contact technical support.

Sample volume is not
correct.

Incorrect volume calibration

Repeat the volume calibration.

Incorrect tube length is
specified in the sampling
program.

Make sure that the correct tube
length is in the sampling program.

Intake tube does not purge
completely.

Make sure that the intake tube is as
vertical and as short as possible.

Strainer is not completely
submerged.

Install the shallow depth strainer
(2071 or 4652).

Worn pump tubing and/or
roller assembly.

Replace the pump tube and/or roller
assembly.

The liquid detector is disabled. Turn the liquid detector on and

complete a volume calibration.

Liquid detector does not
operate properly.

Calibrate the liquid detector with the
same liquid that is sampled.

Section 7 Replacement parts and accessories

W A R N I N G

 

Personal injury hazard. Use of non-approved parts may cause personal injury, damage
to the instrument or equipment malfunction. The replacement parts in this section are
approved by the manufacturer.

Note: Product and Article numbers may vary for some selling regions. Contact the appropriate distributor or refer to
the company website for contact information.

7.1 Bottle kits—refrigerated sampler

Description

Quantity

Item no.

Single bottle kits (includes bottle and full bottle shut off):

10-L (2.5-gal) poly bottle and full bottle shut off

RF010030 

10-L (2.5-gal) glass bottle and full bottle shut off

RF010025 

21-L (5.5-gal) poly bottle and full bottle shut off

RF010060 

Multi-bottle kits (include bottle, retainer and distributor arm):

10-L (2.5-gal) poly bottles, retainer and distributor arm

RF040030 

350-mL (11.8-oz) glass bottles, retainer and distributor arm

24 

RF240350 

1-L (33.8-oz) poly bottles, retainer and distributor arm

24 

RF241000 

English

   

27

Summary of Contents for AS950 AWRS





































Reviews: