manualshive.com logo in svg

Haag-Streit IM 900, Instructions For Use Manual, Page: 15 / 23

Share
Download
Haag-Streit IM 900 Instructions For Use Manual Download Page 15

15

DEUTSCH

ENGLISH 

FRANÇAIS

ITALIANO

ESPAÑOL

NEDERLANDS

PORTUGUÊS

SVENSKA

DEUTSCH

ENGLISH

FRANÇAIS

ITALIANO

ESPAÑOL

NEDERLANDS

PORTUGUÊS

SVENSKA

© HAAG‑STREIT AG, 3098 Koeniz, Switzerland ‑ HS‑Doc. no. 1500.7220551‑04070 – 2021 – 08

7 Decommissioning

Press the On/Off key (53) on the release module RM02 briefly to switch off the LED

illumination after the examination. This does not switch off the camera. This is

signaled with green pulsing. Pressing the key for approx. 3 sec. switches off the

release module completely and the operational control LED (52) goes out. The

camera has no separate On/Off switch. It switches off automatically when the PC is

switched off.

NOTE!

The On/Off key on the release module RM02 does not disconnect the

device from the electric mains. Disconnect the power supply from the

mains by unplugging the mains connector if you do not intend to use it

for an extended period of time.

8 Technical data

8.1 Power supply

Type

ICCNEXERGY, ELPAC POWER SYSTEMS

Model

MWA030018B-10A REF 1022106

Mains voltage

100 − 240 VAC

Current consumption

0.8 A

Operating frequency

50 − 60 Hz

8.2 Dimensions

Camera module CM03

Weight:

2.6 kg (incl. packaging)

Dimensions L × W × H:

190 × 127 × 76 mm

Packaging L × W × H:

380 × 270 × 130 mm

8.3 Minimum PC requirements

Processor type

Intel i5, 5th gen or higher with 4 cores.

NOTE!

• 6th gen is not recommended.

• 2 cores with hyperthreading are not

recommended.

RAM

8 GB RAM if PC is exclusively used to operate the

imaging module.

16 GB RAM if third-party applications such as patient

administration software are to be used alongside

EyeSuite.

Use 2 RAM module.

Hard disk

At least 500 GB (NTFS data system).

Graphics

Graphics card with at least 2 GB memory (Nvidia or

AMD chip set recommended).

OpenGL 2.0

Monitor

At least 19", 1920 × 1080 pixel resolution.

Operating system

Windows 8.1, Windows 10, Windows 11.

64-bit system only.

PCI slot

PCI-Express 3.0

PCI Express card

Chip set by Renesas / NEC.

8.4 Camera

Camera beam:

Beam path right (from the point of view of the doctor)

Interface:

USB 3.0

Frame rate:

30 fps (frames per second)

Power consumption:

5 V

/ 600 mA

Summary of Contents for IM 900
























Reviews:

No comments