H3C WA2600 Series Command Reference Manual Download Page 20

Page: 20 / 131

4-7

interface interface-type interface-number:

Clears the ARP entries for the interface specified by the

argument

interface-type interface-number

Description

Use the

reset arp

command to clear ARP entries except authorized ARP entries from the ARP mapping

table.

With

interface

interface-type interface-number

slot slot-id

specified, the command clears only

dynamic ARP entries of the interface or the slot.

Related commands:

arp static

and

display arp

Examples

# Clear all static ARP entries.

<Sysname> reset arp static

Gratuitous ARP Configuration Commands

gratuitous-arp-sending enable

Syntax

gratuitous-arp-sending enable

undo gratuitous-arp-sending enable

View

System view

Default Level

2: System level

Parameters

None

Description

Use the

gratuitous-arp-sending enable

command to enable the AP to send gratuitous ARP packets

when receiving ARP requests from another network segment.

Use the

undo gratuitous-arp-sending enable

command to restore the default.

By default, an AP cannot send gratuitous ARP packets when receiving ARP requests from another

network segment.

Examples

# Disable the gratuitous ARP packet sending function.

<Sysname> system-view

[Sysname] undo gratuitous-arp-sending enable

gratuitous-arp-learning enable

Syntax

gratuitous-arp-learning enable

undo gratuitous-arp-learning enable

Summary of Contents for WA2600 Series




































































































































Search results

Summary of Contents for WA2600 Series

Reviews:

Related manuals for WA2600 Series

Brands by name

Popular brands

H3C WA2600 Series, Command Reference Manual

Search results

Summary of Contents for WA2600 Series

Reviews:

Related manuals for WA2600 Series

Brands by name

Popular brands