background image

b. 

Use the 

display traffic classifier user-defined

 and 

display traffic 

behavior user-defined

 commands to check whether the traffic classes and traffic 

behaviors in the QoS policy are correctly configured. 

If yes, go to step 4. If not, correct the configuration. 

3. 

Use the 

display packet-filter

 command to check whether the packet filter configuration 

is correct. 

If yes, go to step 4. If not, correct the configuration. 

4. 

Use the 

display acl

 command to check whether the ACL rule configuration is correct. 

If yes, go to step 5. If not, correct the configuration. 

5. 

If the issue persists, contact H3C Support. 

Related commands 

This section lists the commands that you might use for troubleshooting ACLs.  

 

Command Description 

display acl resource 

Displays QoS and ACL resource usage. 

display packet-filter 

Displays ACL application information for packet 
filtering. 

display qos policy global 

Displays QoS policies applied globally.

 

display qos policy interface 

Displays the QoS policies applied to interfaces.

 

display qos vlan-policy 

Displays QoS policies applied to VLANs.

 

display traffic behavior user-defined 

Displays traffic behaviors.

 

display traffic classifier user-defined

Displays traffic classes.

 

 

Troubleshooting link aggregation 

Link aggregation failure 

Symptom 

An aggregate link cannot be set up. 

Summary of Contents for SOHO IE4100



















Reviews: