background image

15 

b. 

Execute the 

poe update

 command to upgrade the PSE software. 

<Sysname> system-view 

[Sysname] poe update full ver_3_9_0_release.bin  

This command will fully update firmware on the specific PSE(s), Continue? [Y/N]:y 

System is downloading firmware into the hardware. Please wait .................. 

Update firmware on the specific PSE(s) successfully! 

The output shows that the PSE software is upgraded successfully. 

c. 

Execute the 

display poe device

 command again. If the 

State

 field displays 

on

 or 

off

, it 

indicates that the PSE failure has been resolved. 

[Sysname] display poe device 

PSE ID  SlotNo SubSNo PortNum  MaxPower(W)  State   Model 

 1      1      0      24       370          on     LSW-BCM-POE 

2. 

Verify that the PSE is supplying power correctly. 

a. 

Execute the 

display poe pse

 command in any view to check the current power, average 

power, and peak power of the PSE, and the state of non-standard PD detection. 

[Sysname] display poe pse 

 PSE ID                           : 1 

 PSE Slot No                      : 1 

 PSE SubSlot No                   : 0 

 PSE Model                        : LSW-BCM-POE 

 PSE Current Power                : 0        W 

 PSE Average Power                : 0        W 

 PSE Peak Power                   : 0        W 

 PSE Max Power                    : 370      W 

 PSE Remaining Guaranteed         : 370      W 

 PSE CPLD Version                 : - 

 PSE Software Version             : 130 

 PSE Hardware Version             : 57617 

 PSE Legacy Detection             : disabled 

 PSE Utilization-threshold        : 80 

b. 

Replace the current PSE with another one with larger power if the current power, average 
power, and peak power of the PSE all reach or are close to the maximum PSE power. 

c. 

Execute the 

poe legacy enable

 command to enable the PSE to detect nonstandard PDs 

if the 

PSE Legacy Detection

 field displays 

disabled

3. 

Verify that the PI is supplying power correctly. 

a. 

Execute the

 display poe interface

 

interface-type interface-number 

command in any view to check the current, average, and peak power, and the current and 
voltage of the PI. 

[Sysname] display poe interface Ethernet 1/0/1 

 Port Power Enabled               : disabled 

 Port Power Priority              : low 

 Port Operating Status            : power-deny 

 Port IEEE Class                  : 0 

 Port Detection Status            : disabled 

 Port Power Mode                  : signal 

 Port Current Power               : 0        mW 

 Port Average Power               : 0        mW 

 Port Peak Power                  : 0        mW 

Summary of Contents for SOHO IE4100



















Reviews: