H3C SecPath Series Command Manual Download Page 1

Page: 1 / 42

Command Manual – User Access
H3C SecPath Series Security Products

Table of Contents

Table of Contents

Chapter 1 PPP Configuration Commands .................................................................................. 1-1

1.1 PPP Configuration Commands.......................................................................................... 1-1

1.1.1 debugging ppp { all | cbcp | ccp | scp }.................................................................... 1-1

1.1.2 debugging ppp { chap | compression | pap | vjcomp packet }................................. 1-2

1.1.3 debugging ppp { core | ip | ipcp | lcp | lqc | mp } ..................................................... 1-3

1.1.4 link-protocol ppp ...................................................................................................... 1-4

1.1.5 ppp authentication-mode......................................................................................... 1-4

1.1.6 ppp chap password ................................................................................................. 1-5

1.1.7 ppp chap user.......................................................................................................... 1-6

1.1.8 ppp ipcp dns ............................................................................................................ 1-7

1.1.9 ppp ipcp dns admit-any ........................................................................................... 1-8

1.1.10 ppp ipcp remote-address forced ........................................................................... 1-8

1.1.11 ppp ipcp dns request............................................................................................. 1-9

1.1.12 ppp lqc................................................................................................................. 1-10

1.1.13 ppp pap local-user............................................................................................... 1-11

1.1.14 ppp timer negotiate ............................................................................................. 1-12

1.1.15 timer hold............................................................................................................. 1-12

1.2 PPP Link Efficiency Mechanism Commands................................................................... 1-13

1.2.1 debugging ppp compression iphc rtp .................................................................... 1-13

1.2.2 debugging ppp compression iphc tcp ................................................................... 1-14

1.2.3 display ppp compression iphc rtp.......................................................................... 1-15

1.2.4 display ppp compression iphc tcp ......................................................................... 1-15

1.2.5 display ppp compression stac-lzs ......................................................................... 1-16

1.2.6 ip tcp vjcompress................................................................................................... 1-16

1.2.7 ppp compression iphc ........................................................................................... 1-17

1.2.8 ppp compression iphc rtp-connections ................................................................. 1-18

1.2.9 ppp compression iphc tcp-connections ................................................................. 1-19

1.2.10 ppp compression stac-lzs.................................................................................... 1-19

1.2.11 reset ppp compression iphc ................................................................................ 1-20

1.2.12 reset ppp compression stac-lzs........................................................................... 1-21

Chapter 2 PPPoE Server Configuration Commands ................................................................. 2-1

2.1.1 display pppoe-server session.................................................................................. 2-1

2.1.2 pppoe-server bind virtual-template.......................................................................... 2-2

2.1.3 pppoe-server log-information off ............................................................................. 2-3

2.1.4 pppoe-server max-sessions local-mac ................................................................... 2-3

2.1.5 pppoe-server max-sessions remote-mac................................................................ 2-4

2.1.6 pppoe-server max-sessions total ............................................................................ 2-4

Summary of Contents for SecPath Series











































Search results

Summary of Contents for SecPath Series

Reviews:

Related manuals for SecPath Series

Brands by name

Popular brands

H3C SecPath Series, Command Manual

Search results

Summary of Contents for SecPath Series

Reviews:

Related manuals for SecPath Series

Brands by name

Popular brands