background image

 

9-40 

Description 

Use the 

ospfv3 timer retransmit

 command to configure the LSA retransmission interval for an 

interface in an instance.   

Use the 

undo ospfv3 timer retransmit

 command to restore the default.   

The interval defaults to 5 seconds. 

After sending a LSA to its neighbor, the device waits for an acknowledgement. If receiving no 

acknowledgement after the LSA retransmission interval elapses, it will retransmit the LSA.   

The LSA retransmission interval should not be too small for avoidance of unnecessary 

retransmissions.  

Examples 

# Configure the LSA retransmission interval on an interface in instance 1 as 12 seconds. 

<Sysname> system-view 

[Sysname] interface vlan-interface 10 

[Sysname-Vlan-interface10] ospfv3 timer retransmit 12 instance 1 

ospfv3 timer poll   

Syntax 

ospfv3 timer poll seconds 

[

 instance instance-id 

undo ospfv3 timer poll 

[

 instance instance-id 

View 

Interface view   

Default Level 

2: System level   

Parameters 

seconds

: Poll interval in seconds, in the range 1 to 65535. 

instance-id

: Interface instance ID, in the range 0 to 255. The default is 0. 

Description 

Use the 

ospfv3 timer poll 

command to set the poll interval on an NBMA interface. 

Use the 

undo ospfv3 timer poll

 command to restore the default value. 

By default, the poll interval is 120 seconds. 

Examples 

# Set the poll timer interval on the current interface to 130 seconds. 

<Sysname> system-view 

[Sysname] interface vlan-interface 10 

[Sysname-Vlan-interface10] ospf timer poll 130

 

ospfv3 trans-delay 

Syntax 

ospfv3 trans-delay

 

seconds

 [ 

instance instance-id

 ] 

undo ospfv3 trans-delay

 [ 

instance instance-id

 ]

 

Summary of Contents for s5820x series









































































































































































































































































































































































































































































































Reviews: