manualshive.com logo in svg

H3C s5820x series, Configuration Manual, Page: 190 / 209

Share
Download
H3C s5820x series Configuration Manual Download Page 190

 

17-29 

 

z

 

To encapsulate and forward IPv4 packets whose destination address does not belong to the 

network segment where the receiving tunnel interface resides, you need to configure a static 

route or dynamic routing for forwarding those packets through this tunnel interface. If you 

configure a static route to that destination IPv4 address, specify this tunnel interface as the 

outbound interface, or the peer tunnel interface as the next hop. A similar configuration needs to 

be performed at the other tunnel end. If you configure dynamic routing at both ends, enable the 

dynamic routing protocol on both tunnel interfaces. For the detailed configuration, 

see

 

Static 

Routing Configuration

 or 

other routing protocol configurations in the Layer 3 - IP Routing 

Configuration Guide.

 

z

 

Two or more tunnel interfaces using the same encapsulation protocol must have different source 

and destination addresses. 

z

 

If you specify a source interface instead of a source address for the tunnel, the source address of 

the tunnel is the primary IP address of the source interface. 

 

Configuration Example 

Network requirements 

The two subnets Group 1 and Group 2 in the private network running IPv4 are interconnected over the 

IPv6 network by using an IPv4 over IPv6 tunnel between Switch A and Switch B. 

Figure 17-12 

Network diagram for an IPv4 over IPv6 tunnel 

 

 

 

Configuration procedure 

 

 

Make sure that Switch A and Switch B have the corresponding VLAN interfaces created and can 

reach to each other. 

 

z

 

Configuration on Switch A 

# Enable IPv6. 

<SwitchA> system-view 

Summary of Contents for s5820x series


















































































































































































































Reviews:

No comments