manualshive.com logo in svg

H3C S5810-50S, Installation Manual, Page: 45 / 73

Share
Download
H3C S5810-50S Installation Manual Download Page 45

 

4-9 

    PCB Version     : Ver.A 

Mac Address     : 00E0FC005810 

 

Press Ctrl-B to enter Extended Boot menu...5   

In normal startup mode, the waiting time here is five seconds. If you press 

Ctrl

 + 

B

 within five seconds, 

the Boot ROM menu is displayed. If you perform no operation or press a key other than 

Ctrl 

+ 

B

 within 

five seconds, the system begins to automatically start up and the following information is displayed: 

Starting to get the main application file--flash:/s5810 RELEASE.bin!... 

.................................................................. 

The main application file is self-decompressing................................ 

............................................................................... 

............................................................................... 

............................................................................... 

............................................................................... 

Done! 

System is starting... 

 

Board checking.....................................LSW158150S 

Switch chip selftest......................................OK! 

SDRAM fast selftest.................................NOT TEST! 

Flash fast selftest.......................................OK! 

PHY selftest..............................................OK! 

CPLD selftest.............................................OK! 

Please check port leds..............................finished! 

 

User interface aux0 is available. 

 

Press ENTER to get started. 

The appearance of "Press ENTER to get started" indicates that the automatic startup of the switch is 
complete.  

Press 

Enter

. The following prompt is displayed:  

<H3C> 

You can configure the switch now. 

 

 

z

 

To switch to the fast start mode, select 

9

 from the Boot ROM menu, enter 

N

 after the prompt 

information is displayed, and then reboot the system. 

z

 

The H3C series switches provide abundant command views. For detailed descriptions about the 
configuration commands and CLI, refer to 

H3C S5810 Series Ethernet Switches  Operation Manual

 

and 

H3C S5810 Series Ethernet Switches  Command Manual

. 

 

Summary of Contents for S5810-50S










































































Reviews:

No comments