manualshive.com logo in svg

H3C S5810-50S, Installation Manual, Page: 17 / 73

Share
Download
H3C S5810-50S Installation Manual Download Page 17

 

1-11

 

Table 1-12 

Seven-segment LED description 

Status 

Mark 

System LED 

(SYS) status 

Seven-segment LED status

Description 

Flashing green 

The LED displays the specific 
numbers one by one. 

POST running. The LED 
displays the POST test ID. 

Flashing red 

The LED flashes the specific 
numbers. 

POST failed. The LED flashes 
the POST test ID of the failed 
test. 

Flashing green 

A bar rotates clockwise 
around the LED. 

 

 

Software loading 

Steady red 

The LED flashes and displays 

F

. 

 

 

Fan failure 

Steady red 

The LED flashes and  displays 

t

. 

 

 

Over-temperature alarm 

The LED displays 

C

. 

 

The current switch is the 
command switch in the cluster.

The LED displays 

S

. 

 

The current switch is a member 
switch in the cluster. 

The LED displays 

c

. 

 

The current switch is a 
candidate switch in the cluster. 

Unit 

Steady green 

The LED displays the specific 
numbers. 

The member ID of the current 
switch. 

 

Port Mode LED 

The port mode LED on the S5810 series can display the working status of a port for you to obtain more 
device information. You can use the port mode switching button to change the status of the port mode 
LED. 

Table 1-13 

Port mode LED description 

LED 

Status 

Description 

Mode 

Steady green 

Indicates port rate. 

Summary of Contents for S5810-50S










































































Reviews:

No comments