manualshive.com logo in svg

H3C S5810-50S, Installation Manual, Page: 44 / 73

Share
Download
H3C S5810-50S Installation Manual Download Page 44

 

4-8 

2. Select application file to boot 

3. Display all files in flash 

4. Delete file from flash 

5. Modify BootRom password 

6. Enter BootRom upgrade menu 

7. Skip current configuration file 

8. Set BootRom password recovery 

9. Set switch startup mode 

0. Reboot 

 

Enter your choice(0-9): 

Enter 

9

. The system prompts you to change the startup mode: 

The current mode is fast startup mode! 

Are you sure you want to change it to full startup mode? Yes or No (Y/N): 

Enter 

Y

. The system displays the following information:  

Setting...Done! 

 

   BOOT MENU 

 

1. Download application file to flash 

2. Select application file to boot 

3. Display all files in flash 

4. Delete file from flash 

5. Modify BootRom password 

6. Enter BootRom upgrade menu 

7. Skip current system configuration 

8. Set BootRom password recovery 

9. Set switch startup mode 

0. Reboot 

 

Enter your choice(0-9):   

Enter 

0

. The system reboots in fast startup mode and displays the following information: 

Starting...... 

 

    ************************************************************************ 

    *                                                                      * 

    *                 H3C S5810-50S BOOTROM, Version 107                   * 

    *                                                                      * 

    ************************************************************************ 

Copyright (c) 2004-2009 Hangzhou H3C Technologies Co., Ltd. 

 

    Creation Date   : Feb 19 2009,09:02:02 

    CPU Clock Speed : 750MHz 

    Memory Size     : 512MB 

    Flash Size      : 256MB 

    CPLD Version    : 000 

Summary of Contents for S5810-50S










































































Reviews:

No comments