manualshive.com logo in svg

H3C S12500-X, Command Reference Manual, Page: 35 / 36

Share
Download
H3C S12500-X Command Reference Manual Download Page 35

29 

operate in 

extended

 mode. To relay IRF links, MAC address learning and checking must be 

disabled on the optical transmission devices. 

The system does not dynamically remove IRF port bindings when IRF links are lost, for example, because 

an interface card is removed. To remove IRF port bindings, you must use the 

undo port group interface

 

command. 
For more information about IRF port binding requirements, see 

IRF Configuration Guide

. 

Examples 

# (In standalone mode.) Bind Ten-GigabitEthernet 2/0/1 to IRF-port 1. 

<Sysname> system-view 

[Sysname] irf-port 1 

[Sysname-irf-port1] port group interface ten-gigabitethernet 2/0/1 

# (In IRF mode.) Bind Ten-GigabitEthernet 1/2/0/1 to IRF-port 1 of member 1. 

<Sysname> system-view 

[Sysname] interface ten-gigabitethernet 1/2/0/1 

[Sysname-Ten-GigabitEthernet1/2/0/1] shutdown 

[Sysname-Ten-GigabitEthernet1/2/0/1] quit 

[Sysname] irf-port 1/1 

[Sysname-irf-port1/1] port group interface ten-gigabitethernet 1/2/0/1 

[Sysname-irf-port1/1] quit 

[Sysname] interface ten-gigabitethernet 1/2/0/1 

[Sysname-Ten-GigabitEthernet1/2/0/1] undo shutdown 

[Sysname-Ten-GigabitEthernet1/2/0/1] quit 

Related commands 

irf-port 
 

Summary of Contents for S12500-X





































Reviews:

No comments