manualshive.com logo in svg

H3C S12500-X, Command Reference Manual, Page: 21 / 36

Share
Download
H3C S12500-X Command Reference Manual Download Page 21

15 

Views 

System view 

Predefined user roles 

network-admin 
mdc-admin 

Parameters 

member-id

: Assigns an IRF member ID to the device. The value must be 1 or 2.  

Usage guidelines 

You must assign an IRF member ID to a device before enabling its IRF mode. The member ID takes effect 

after the IRF mode is enabled. This member ID must be unique among all IRF member devices. 
To change the member ID of a device in IRF mode, use the 

irf member 

member-id

 renumber 

new-member-id

 command. The new member ID takes effect at reboot.  

Examples 

# (In standalone mode.) Assign member ID 2 to the device. 

<Sysname> system-view 

[sysname] irf member 2 

Related commands 

irf member renumber 

irf member description 

Use 

irf member description

 to configure a description for an IRF member. 

Use 

undo irf member description

 to restore the default. 

Syntax 

irf member 

member-id

 description 

text

 

undo irf member 

member-id

 description

 

Default 

No description is configured for any IRF member. 

Views 

System view 

Predefined user roles 

network-admin 
mdc-admin 

Parameters 

member-id

: Specifies the ID of an IRF member. The value must be 1 or 2. 

text

: Configures the IRF member description, a string of 1 to 127 characters. 

Usage guidelines 

Configure a description to describe the location or purpose of a member device. 

Summary of Contents for S12500-X





































Reviews:

No comments