A
A
24
The .RCU .has .the .ability .to .
learn
.the .commands .of .other .remote .control .
units, .such .as .TV .remotes .or .VCR .remotes . . .This .allows .the .most-used .
commands .on .those .remotes .to .be .combined .on .the .RCU . . .These .original .
remote .control .units .are .also .known .as .source .remotes . . .Learning .is .not .
active .in .the .PC .mode .
Learning Tips
1 . .All .learned .functions .for .a .mode .can .be .erased .if .you .program .a .different .
device .to .that .mode .
2 . .Perform .the .learning .process .in .low-light .areas .because .too .much .
ambient .light .might .cause .interference .with .the .infrared .(IR) .signals .
of .the .remotes .
3 . .Use .fresh .batteries .in .both .the .RCU .and .the .original .remote . .
4 . . . .Set .the .two .remotes .on .a .table .or .other .flat .surface, .and . .
don’t .move .them .around .while .learning .
Code Learning
Codes .from .the .Remote .Code .List .include .basic .functionality .for . .
each .component .they .control . . .Once .you .have .programmed .in .the . .
code .for .your .specific .component .(using .either .the .Automatic .Code . .
Search .or .Direct .Entry .method), .you .can .customize .the .RCU .to .perform .
certain .functions .from .your .original .remote(s) .that .were .not .embedded .
in .the .preset .code . . .The .RCU .has .the .ability .to .learn .and .store .commands .
from .your .original .remote(s) .under .the .mode(s) .of .your .choice . . .
Learning Commands
For .the .following .section, .the .TV .remote .control .unit .will .be .used .as .an .
example . . .Learning .from .other .types .of .remotes .will .be .done .in .a . .
similar .way .
1) .First .press .and .hold .the .device .button .on .the .RCU .for .the .component .
remote .you .are .learning .from .(the .TV .button .on .the .RCU, .for .
example) .then .press .and .hold .the .
RECORD
.button .on .the .RCU .
2) .Keep .pressing .both .buttons .until .all .device .mode .buttons .turn .on . .
Release .both .buttons . .The .selected .device .button .will .remain .on .
indicating .which .device .is .being .programmed .
NOTE: . .The .first .two .steps .to .learn .commands .must .be .completed .within .2 .
seconds .to .learn .without .entering .the .Menu .Program .Method .
Learning
Remotes .should .
not .be
more .than .
2” .apart
23
Learning
(continued)
3) .On .the .RCU, .press .and .release .the .button .where .you .want .to .store .the .new .function .(the .
device .button .turns .off) .
Note:
If you press an invalid button on the remote, the device mode button flashes 4 times
to alert you. You’ll have to repeat step 3.
4) .Position .the .source .remote .facing .the .bottom .of .the .RCU .no .more .than .2 .inches .apart . .
Press .and .hold .the .button .of .the .source .remote .that .has .the .functionality .you .are .
recording . .Keep .pressing .the .button .until .the .RCU .device .mode .button .light .turns .on .(the .
source .function .has .been .saved .to .the .TV .mode .on .the .RCU) . .
Note:
If all device mode buttons flash 4 times, the function wasn’t learned. Try again
starting with Step 1.
5) .The .RCU .remains .in .the .“learning .mode” .so .you .can .continue .adding .functions .to .
different .buttons .by .repeating .steps .3 .and .4 . .
6) .Press .
CLEAR
.to .exit .the .learning .mode .
Clearing an Individual Learned Function
To .delete .a .learned .button .function, .use .the .procedure .below .
1 . .Press .and .hold .the .device .mode .button .(the .device .button .lights) . . .Then .press .and .hold .
the .
STOP
.button . . .Hold .both .buttons .depressed .until .all .device .mode .buttons .turn .on .
NOTE: . .This .step .to .must .be .completed .within .2 .seconds .to .be .able .to .clear .an .individual .
learned .function .without .entering .the .Menu .Program .Method . . .
2 . .Release .both .buttons . . .The .device .mode .button .turns .on .indicating .that .the .RCU .is .now .in .
the .Clear .Learned .Function .mode .for .that .device .
3 . .Press .and .release .the .button .where .learning .is .to .be .cleared . . .The .device .mode .button .
blinks .off .then .back .on .indicating .that .the .function .was .cleared .successfully . . .
4 . .Repeat .Steps .1 .through .3 .until .all .the .buttons’ .learned .functions .have .been .cleared .
.
Note:
If an invalid button is pressed, the device mode button flashes 4 times, the
selected component button stays on, and the RCU remains in Clear Learned Function
mode. Repeat Step 3 to continue the clearing process.
5 . .Press .the .
CLEAR
.button .to .return .the .RCU .to .normal .operation .
Deleting All Learned Functions - One Device
To .delete .all .learned .functions .for .one .device .at .one .time, .use .the .procedure .below .
1 . . . .Press .and .hold .the .device .mode .button .(the .device .button .lights) . . .Then .press .and .hold .
the .
CLEAR
.button . . .Hold .both .buttons .depressed .until .all .device .mode .buttons .turn .on .
NOTE: . .This .step .to .must .be .completed .within .2 .seconds .to .be .able .to .clear .all .learned
All manuals and user guides at all-guides.com
