A
A
Programming Methods
(continued)
4 . .Press .and .release .
PLAY
, .then .wait .5 .seconds .or .until .the .device .button .stops .flashing . . .At .
this .point .the .RCU .is .searching .for .the .correct .code .to .program . .If, .after .5 .seconds, .the .
device .you .want .to .operate .does .not .turn .off, .press .PLAY .again .to .tell .the .RCU .to .search .the .
next .set .of .codes . . .Continue .pressing .and .releasing .
PLAY
.until .the .device .turns .off .or .you .
have .searched .through .all .of .the .codes . .The .device .buttons .flash .when .all .codes .have .been .
searched, .the .device .button .turns .off, .and .after .30 .seconds .the .RCU .exits .the
Automatic
Code Search
.mode .
If .the .component .you .want .to .control .
does
.turn .off:
1 . .Press .and .release .REVERSE, .then .wait .2 .seconds . .Repeat .this .step .until .the .component .
turns .back .on .
2 . .To .finish, .press .STOP .and .the .devices .buttons .on .the .RCU .turn .off . . .The .RCU .will .automatically .
exit .the .
Automatic Code Search
.mode .
Using Direct Entry
1 . .Turn .on .the .device .you .want .to .operate .(TV, .DVD .player, .etc .)
2 . .Look .up .the .brand .and .code .number(s) .for .the .device .in .the .Remote .Code .List .at .the .end .
of .this .booklet . . .
3 . .Press .and .hold .the .device .button .you .want .to .program .((
TV, AUX
, .etc .) .on .the .RCU .
4 . .Enter .the .4-digit .code .from .the .Remote .Code .List . .
5 . .Release .the .device .button, .if .all .the .mode .buttons .flash, .you .have .entered .an .invalid .
code . . .Otherwise, .point .the .RCU .at .the .device, .and .then .press .the .ON/OFF .button .to .see .
if .the .device .responds .to .the .command .
.
• .If .you .get .no .response, .repeat .these .steps .using .the .next .code .listed .for . .
.
. . .your .brand, .until .the .device .responds .to .the .remote .commands .
.
• .If .you .try .all .the .codes .for .your .device .brand .and .none .work, .try .the . . .
.
. . .automatic .code .search .method . .If .automatic .code .search .doesn’t .find .the . .
.
. . .code, .the .remote .is .not .compatible .with .your .component .
Because .the .RCU .controls .more .than .one .device, .you .must .first .“tell” .it .which .device .you .
wish .to .operate . . .For .example, .if .you .wish .to .operate .the .TV, .you .must .first .press .the .
TV
.
mode .button .on .the .RCU .to .put .it .in .the .TV .mode .
The .RCU .stays .in .the .chosen .mode .until .you .change .it . . .If .the .RCU .is .in .the .TV .mode, .you .
must .change .the .mode .in .order .to .operate .other .components . . .For .example, .if .you .are .in .
the .TV .mode .and .you .wish .to .turn .off .the .Cable .Box, .you .must .first .press .the .
CAB/SAT
.
button .then .the .On/Off .button . . .Return .to .the .TV .mode .by .pressing .the .TV .mode .button .
Programming Methods
(continued)
Volume Punch Through
The .Volume .Punch .Through .feature .allows .you .to .control .the .volume .without .exiting .the .
current .mode . .When .Punch .Through .is .enabled, .the
VOL+
, .
VOL-
, .and .
MUTE
.keys .will .
always .control .the .Punch .Through .device . .By .default .the .TV .is .the .Volume .Punch .Through .
device . .To .disable .Volume .Punch .Through, .see .the .“Disabling .Volume .Punch .Through” .
Section .below . .
Note: .Volume .Punch .Through .only .applies .to .the .three .IR .Mode .Device .Buttons .
(TV,
CAB/SAT, and AUX)
.
Note:
The remote must be programmed via Automatic Code Search or Direct Entry
before enabling Volume Punch Through.
To .change .the .Volume .Punch .Through .device .or .enable .Volume .Punch .Through: .
1 . . .Press .and .hold .the .device .button .of .the .device .you .want .to .Punch .Through . .
(
TV, AUX,
.etc .) .on .the .RCU .
2 . . .Press .and .hold .the .
VOL-
.button .until .all .device .buttons .on .the .RCU .turn .on, . .
then .release .both .buttons . .
Volume .Punch .Through .is .now .enabled .for .the .selected .device . .NOTE: . .The .steps .to .enable .
Volume .Punch .Through .must .be .completed .within .2 .seconds .to .activate .without .entering .
the .Menu .Program .Method . .
Disabling Volume Punch Through
To .disable .Volume .Punch .Through: .
1 . .Press .and .hold .any .device .button .(TV, .AUX, .etc .) .on .the .RCU .
2 . . .While .holding .the .device .button, .press .and .hold .the .MUTE .button .until .all .of .the .device .
buttons .turn .on .
Volume .Punch .Through .is .now .disabled .
NOTE: . .The .steps .to .disable .Volume .Punch .Through .must .be .completed .within .2 .seconds .to .
successfully .disable .without .entering .the .Menu .Program .Method . . .
Note
: If an invalid button is pressed, all device buttons blink 4 times and turn off. At this
point, you must start over.
Once .Volume .Punch .Through .is .disabled, .the .
VOL+
, .
VOL-
, .and .
MUTE
.keys .will .control .
the .device .currently .selected .by .the .Device .button .(
PC, TV, CAB/SAT,
.or .
AUX
) . .To .
enable .Volume .Punch .Through, .see .the .“Volume .Punch .Through” .Section .above .
21
22
All manuals and user guides at all-guides.com
