manualshive.com logo in svg

GUITAR KIT WORLD EXP-style Guitar Kit, Assembly Manual

Share
Download
GUITAR KIT WORLD EXP-style Guitar Kit Assembly Manual Download Page 29

placed on the neck. Be sure to continue to check your tuning through the entire setup
process.

Adjusting the action

Action refers to the height of the strings from the fretboard of the guitar. This is usually
measured from the top of the 12th fret to the underside of the low E string.

A good starting point is 2.4mm on the low E side and 1.6mm on the high E side, taking into
account the different string gauges. Make sure the guitar is in tune before checking and
making adjustments.

Action is adjusted at the bridge. Loosen the bridge posts to raise the action, tighten the
bridge posts to lower the action.

Intonating the guitar

Intonation, in essence means, is the guitar in tune with itself. You can check this by tuning
to standard tuning and then checking the strings at the 12th fret (an octave up from the
open string). If the pitch is sharp you will need to lengthen the string length. If flat you will
need to shorten it.

29

Summary of Contents for EXP-style Guitar Kit
































Reviews:

No comments

Brands by name

Popular brands

Load more brands